Results 31 to 40 of about 1,402 (150)
Wear mechanisms in polyoxymethylene spur gears
Wear, 2019 Abstract The interaction of a polymer-steel spur gear pair is naturally prone to cause wear of the softer polymer material. Experimental equipment was therefore designed and constructed to run a polymer-steel spur gear pair with sufficiently accurate instrumentation such that the load and speed could be measured under a range of operating conditions.
Evans, Stuart, Keogh, Patrick
openaire +2 more sources
Simulation of Rotational Vibration of Spur Gears
Bulletin of JSME, 1983 This paper introduces a developed simulator on a rotational vibration and a strain at a root of a tooth, on a power transmission spur gear. The simulator solves a differential equation with one degree of freedom in consideration of the behaviour of the stiffness around tooth tip meshing.
UMEZAWA, Kiyohiko +2 more
openaire +3 more sources
Reduction of Noise and Vibration of Spur Gear by Using Asymmetric Teeth Profiles with Tip Relief
Journal of Engineering, 2015 Reduction of noise and vibration in spur gear experimentally by using asymmetric teeth profiles with tip relief was presented. Both of classical (symmetric) and asymmetric (with and without tip relief) spur gears are used in this work.
Mohammad Qasim Abdullah +2 more
doaj +2 more sources
New Method of Tooth Pitch Deviation Measurement based on Laser Tracker for Mega Spur Gear
Jixie chuandong, 2019 To measure pitch deviation of mega spur gears, a new method for measuring the pitch of mega spur gears based on laser tracker is proposed. The measuring ability of laser tracker in large space is used to measure gear groove, and two adjacent pitch error ...
Zhang Bai, Lin Jiachun
doaj
Study on stress intensity factors for crack on involute spur gear tooth
Advances in Mechanical Engineering, 2015 Investigating the stress intensity factors has a great importance to predict the fatigue damage for the involute spur gears. The aim of this article is to reveal the variation laws of stress intensity factors for crack on the involute spur gear tooth ...
Jian Cai +3 more
doaj +1 more source
Method of calculation and test of dynamic tooth root strain for high-contact-ratio spur gears
Jixie chuandongObjectiveAiming at the difference of load sharing and dynamic characteristics between high-contact-ratio spur gears and conventional spur gears, a method for calculating the dynamic tooth root strain was proposed considering the dynamic characteristics ...
YU Pengfei +4 more
doaj
Jixie chuandong, 2014 Based on the theory of gear geometry and dynamics,the dynamic calculation model of asymmetric involute spur gear is established,and the programming is produced by Matlab,the dynamic characteristic of asymmetric involute spur gears is studied.The results ...
朱良, 郗军红, 于慧
doaj
Research of the Torsion Stiffness of Involute Gear Transmission
Jixie chuandong, 2017 The gear stiffness calculation has important significance for the study of noise and vibration of power transmission system. Based on the finite element calculation of the software Abaqus,the torsional mesh stiffness of spur gear with involute profile is
Zhou Xin +3 more
doaj
Nonlinear Dynamic Analysis of a Spur Gear Pair System with Wear Considering the Meshing Position
LubricantsIn this paper, a nonlinear dynamic model of a parallel shaft gear system consisting of two involute spur gears is developed to investigate the coupling effect between the gradual surface wear of gear teeth over time and nonlinear dynamic characteristics.
Zhibo Geng +5 more
doaj +1 more source
Jixie chuandong, 2017 Aiming at the real meshing state of high speed spur gear,the calculation mathematical model of line contact elastohydrodynamic lubrication is established,the model including Reynolds,elasticity and load balance equations etc.
Fang Te, Liu Shaojun
doaj