Results 101 to 110 of about 393 (126)

Microstructural Characterization and Mechanical Properties of Friction-Welded IN718 and SS410 Dissimilar Joint

Metallography, Microstructure, and Analysis, 2018
Continuous drive friction welding studies on IN718 and SS410 dissimilar combination have been investigated. The influence of friction-welded parameters on microstructure and mechanical properties was dealt in detail. Six different joints were fabricated by varying rotational speed and friction pressure, by keeping forging pressure and friction time as ...
P Anitha, M. C. Majumder, V. Saravanan, S. Rajakumar   +3 more
openalex   +2 more sources

Experimental investigation of process parameters for pack boronizing of SS410 using anova and machine learning approaches

Surface Topography: Metrology and Properties, 2021
H. Ramakrishnan, R. Balasundaram
openalex   +2 more sources

Investigation on mechanical and metallurgical properties of rotary friction welded In718/SS410 dissimilar materials

Materials Today: Proceedings, 2020
Abstract This research work has detailed the mechanical properties and microstructural behavior of friction welded dissimilar joints. The optimized welding parameters are friction pressure 220 MPa, friction time 10 sec, forging pressure 220 MPa, forging time 8 sec, rotational speed 1300 rpm.
J. Alex Anandaraj, S. Rajakumar, V. Balasubramanian, Vijay Petley   +3 more
openalex   +2 more sources

Microstructure, Nanoindentation and Corrosion Behavior of Colmonoy-5 Deposition on SS410 Substrate Using Laser Cladding Process

Arabian Journal for Science and Engineering, 2022
Sundara Subramanian Karuppasamy, N. Jeyaprakash, Che‐Hua Yang   +2 more
openalex   +2 more sources

Some of the next articles are maybe not open access.

Related searches:

Experimental investigations on laser cladding of NiCrBSi + WC coating on SS410

Materials Today: Proceedings, 2020
Abstract Laser cladding is an emerging technology for depositing coating material over the substrate with less dilution (
A. Gowtham, G. Chaitanya, Jitendra Kumar Katiyar, Aayush Chandak, T.V.K. Gupta   +4 more
openaire   +1 more source

Enhancing microstructural, mechanical and tribological behaviour of AlSiBeTiV high entropy alloy reinforced SS410 through friction stir processing

Tribology International, 2023
S. Ragunath, N. Radhika, S. Aravind Krishna, N. Jeyaprakash   +3 more
openalex   +2 more sources

Study on the Influence of Silicone-Based Magnetorheological Elastomer on Tool Vibration During Turning of Hardened SS410 Steel

Journal of Advanced Manufacturing Systems, 2021
In metal cutting, tool vibration is a significant parameter, which results in high cutting force, increase in tool wear and poor surface quality of the finished product. To control tool vibration, an innovative and a robust damper was required. In this regard, a magnetorheological elastomer was fabricated, and the effect of parameters like the ratio ...
X. Ajay Vasanth, P. Sam Paul, G. Lawrance   +2 more
openalex   +2 more sources

Detection and Classification of Engine Exhaust Weld Joint Defects Using RNN and SVM on SS316L–SS410 and SS310–SS410

Journal of Failure Analysis and Prevention
Rajesh V. Patil, Magnus Löfstrand
openalex   +2 more sources

Assessment of Mechanical and Slurry Erosive Behavior on Laser-Textured Stainless Steel (SS410)

Journal of Materials Engineering and Performance
Mohit Vishnoi, Qasim Murtaza, Paras Kumar   +2 more
openalex   +2 more sources

A neural network model to predict surface roughness during turning of hardened SS410 steel

International Journal of System Assurance Engineering and Management, 2020
In manufacture sector, the surface finish quality has considerable importance that can affect the functioning of a component, and possibly its cost. The surface quality is an significant parameter to evaluate the productivity of machine tools as well as machined components. It is also used as the critical quality indicator for the machined surface.
X. Ajay Vasanth, P. Sam Paul, A. S. Varadarajan   +2 more
openaire   +1 more source