Results 111 to 120 of about 145,868 (280)

Dynamic Testing of Cold Gas Sprayed Bipolar Plates–Porous Transport Layer Coating System in Proton Exchange Membrane Water Electrolysis

Advanced Engineering Materials, EarlyView.
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin, Marvin Erck, Kevin Jasutyn, Katja Radermacher, Andreas Bund, Mario Kurniawan   +5 more
wiley   +1 more source

Thermodynamic and Thermoeconomic investigation of an Integrated Gasification SOFC and Stirling Engine [PDF]

, 2013
Thermodynamic and thermoeconomic investigation of a small scale Integrated Gasification Solid Oxide Fuel Cell (SOFC) and Stirling engine for combined heat and power (CHP) with a net electric capacity of 120kW have been performed.
Rokni, Masoud
core  

Towards Defect Phase Diagrams: From Research Data Management to Automated Workflows

Advanced Engineering Materials, EarlyView.
A research data management infrastructure is presented for the systematic integration of heterogeneous experimental and simulation data required for defect phase diagrams. The approach combines openBIS with a companion application for large‐object storage, automated metadata extraction, provenance tracking and federated data access, thereby supporting ...
Khalil Rejiba, Sang‐Hyeok Lee, Christina Gasper, Martina Freund, Sandra Korte‐Kerzel, Ulrich Kerzel   +5 more
wiley   +1 more source

Neighbor Session Solutions for Integrated Routing Protocols

Applied Sciences
This paper proposes a novel methodology for the design of dual-stack IP routing protocols focused on neighborships and routing messages transport. The first part describes currently used dual-stack IP routing protocols, their history, and key features ...
Martin Kontsek, Pavel Segec, Marek Moravcik, Juraj Smiesko   +3 more
doaj   +1 more source

Impact of Sustainable Binders Based on Lignin and Collagen on the Volume Stability and Mechanical Properties of MgO‐C Refractories with MgO‐C Recyclates

Advanced Engineering Materials, EarlyView.
Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller, Florian Kerber, Kirsten Moritz, Steffen Dudczig, Konstantin Kraushaar, Thomas Schemmel, Jana Hubálková, Patrick Gehre, Christos G. Aneziris   +8 more
wiley   +1 more source

Development of Sustainable MgO–C Refractories Using MgO–C Recyclates and a Novel Eco‐Friendly Fructose–Tannin Binder Crosslinked With Citric Acid

Advanced Engineering Materials, EarlyView.
This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar, Jana Hubálková, Steffen Dudczig, Gert Schmidt, Florian Kerber, Thomas Schemmel, Patrick Gehre, Christos G. Aneziris   +7 more
wiley   +1 more source

Analytical prediction with multidimensional computer programs and experimental verification of the performance, at a variety of operating conditions, of two traveling wave tubes with depressed collectors [PDF]

Experimental and analytical results are compared for two high performance, octave bandwidth TWT's that use depressed collectors (MDC's) to improve the efficiency.
Dayton, J. A., Jr., Kosmahl, H. G., Ramins, P., Stankiewicz, N.   +3 more
core   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Robust Spot Melting by 3D Spot Arrangements in Electron Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This work proposes an approach to replace separately melted contours for spot melting in electron beam powder fusion. Adapting the spot arrangements close to the contour combined with stacking yields a comparable surface quality without the inherent challenges of separate contours, as demonstrated, by electron optical images and roughness measurements.
Tobias Kupfer, Lukas Spano, Sebastian Pohl, Carolin Körner, Matthias Markl   +4 more
wiley   +1 more source

Fostering Innovation: Streamlining Magnetocaloric Materials Research by Digitalization

Advanced Engineering Materials, EarlyView.
Magnetocaloric cooling (MCE) is an environmentally friendly refrigeration method with great potential. Optimizing MCE materials involves the preparation and screening of large quantities of samples, which in turn generates a large amount of data. A digitalization approach is presented that uses ontologies, knowledge graphs, and digital workflows to ...
Simon Bekemeier, Moritz Blum, Luana Caron, Alisa Chirkova, Philipp Cimiano, Basil Ell, Inga Ennen, Michael Feige, Maik Gaerner, Thomas Hilbig, Andreas Hütten, Günter Reiss, Tapas Samanta, Sonja Schöning, Christian Schröder, Lennart Schwan, Chris Taake, Martin Wortmann   +17 more
wiley   +1 more source