Results 141 to 150 of about 7,662 (196)

From hydrogels to eutectogels: Emerging platforms for stretchable electronics

FlexMat, EarlyView.
The transition of wearable electronics toward long‐term reliability requires materials that resist dehydration without sacrificing tissue‐like softness and ionic conductivity. Eutectogels fulfill these demands by immobilizing deep eutectic solvents within tailored polymer networks.
Chang Zhou, Jiancheng Dong, Jiayu Hou, Shiyin Lin, Xingyu Liu, Hao Qiu, Mengting Zheng, Yuduo Zhang, Haijun Zhu, Kangjia Geng, Yidong Peng, Haoran Liu, Xu Zhang, Yunpeng Huang, Tianxi Liu   +14 more
wiley   +1 more source

Implantable drug delivery system: Frontiers of medicine‐engineering interdisciplinary

Interdisciplinary Medicine, EarlyView.
This review systematically summarizes the driving mechanisms of implantable on‐demand drug delivery systems (IDDS), including endogenous, exogenous, and closed‐loop strategies. It highlights the pivotal roles of flexible electronics and miniaturization in enhancing the tissue conformity and spatial adaptability.
Yu Zeng, Rongtai Su, Manyu Zhao, Xin Song, Ran Liu, Yuhao Zhou, Chaojuan Yang, Yanli Jiao, Xiao‐Wei Xiang, Lingqian Chang   +9 more
wiley   +1 more source

Plasmodium sporozoite shows distinct motility patterns in responses to three-dimensional environments. [PDF]

iScience
Liu Z, Li S, Anantha P, Thanakornsombut T, Wu L, Chen J, Tsuchiya R, Tripathi AK, Chen Y, Barman I.   +9 more
europepmc   +1 more source

Single‐Breathhold 3D MR Elastography in the Liver, With Simultaneous R2* and PDFF Mapping

Magnetic Resonance in Medicine, EarlyView.
Purpose To develop a sequence for the rapid acquisition of MR elastography (MRE) parameters in 3D, with simultaneous measurement of proton‐density fat fraction (PDFF) and R2* for multiparametric assessment of liver disease. Methods The proposed sequence uses an interleaved motion‐encoding scheme to acquire 3D volumes of all motion encodings and wave ...
Donovan P Tripp, Anne‐Sophie van Schelt, Omar Darwish, Karl P Kunze, Shamsa Al Harthy, Nader S Metwalli, Ahmed M Gharib, Claudia Prieto, René M Botnar, Ralph Sinkus, Radhouene Neji   +10 more
wiley   +1 more source

LigHTS: Massively Parallel Biomimetic Photo-Functionalization for Imaging-Based Ultra-High-Throughput Screening

Enrico A, Rigolli S, Zimmermann J, Pezzotti M, Torchia E, Di Sante M, Auricchio F, Pasqualini FS.   +7 more
europepmc   +1 more source

Multiphoton imaging for quantification of mesenchymal stem cell survival and distribution in PEG granular hydrogel scaffolds post-implantation into rat cranial bone defects. [PDF]

Biomed Eng Adv
Balouch AP, Francis AZ, Rao VV, Wojda SJ, Anseth KS, Donahue SW.   +5 more
europepmc   +1 more source

Nonlinear Vibration Characteristic Analysis of Electric Vehicle–Road Coupling System

International Journal of Mechanical System Dynamics, EarlyView.
ABSTRACT In‐wheel motor drive is the developing direction of automobile electrification and intelligence. However, the increased unsprung mass in in‐wheel motor‐driven electric vehicles (IWMEVs) leads to higher dynamic tire loads, thereby intensifying vehicle–road coupling interactions. To address this problem, an 11‐degree‐of‐freedom nonlinear dynamic
Guizhen Feng, Shaohua Li, Xuewei Wang
wiley   +1 more source

Experimental and Numerical Investigation on the Dynamic Impact Response of Hat‐Shaped Basalt Fiber‐Reinforced Polymer Composite Structures With Improved Interfacial Properties

Polymer Composites, EarlyView.
Graphical abstract illustrating the experimental design and key findings of the study. ABSTRACT Basalt fiber‐reinforced polymer (BFRP) composites are gaining attention as sustainable alternatives to conventional fiber‐reinforced polymers owing to their favorable mechanical properties and environmental advantages.
Abdulrahman Adeiza Musa, Min Gyu Kim, Anand Prakash Jaiswal, Thuan Ho‐Nguyen‐Tan, Jaesang Yu, Soon Ho Yoon, Azikiwe Peter Onwualu, Minkook Kim   +7 more
wiley   +1 more source

Development of Vertical Wind Turbine Blades Using 4D Printing of Composites

Polymer Composites, EarlyView.
Vertical axis wind turbine: White blade: Commercial. Black blade: Composite. ABSTRACT This paper presents the procedure to make vertical wind turbine blades using the technique of 4D printing of composites (4DPC). The blades are made using carbon/epoxy composite materials with a fiber volume fraction of about 60%.
Emad Fakhimi, Suong Van Hoa
wiley   +1 more source

Multimodal analysis of traction forces and the temperature dynamics of living cells with a diamond-embedded substrate. [PDF]

Biomed Opt Express
Kołodziej T, Mrózek M, Sengottuvel S, Głowacki MJ, Ficek M, Gawlik W, Rajfur Z, Wojciechowski AM.   +7 more
europepmc   +1 more source