Characteristics of Air Impingement From an Orifice on a Target Plate [PDF]
Engineering and Technology Journal, 2013 The present work is an experimental and numerical CFD study of air impingement from orifices of different sizes in the range of (10-40) mm with a step increase of 10 mm.
Adnan A. Abdul Rasool
doaj +1 more source
Study of Effect of Convergence Section Geometric on the Performance of a Sonic Nozzle [PDF]
Journal of Applied Fluid MechanicsCritical flow Venturi nozzles (toroidal, cylindrical, convergent–divergent, or C–D) nozzles) have discharge coefficients predicted through numerical and experimental investigations.
F. A. Kassem, A. A. Zahran, M. Adel
doaj +1 more source
OPTIMIZED CONTROLLER DESIGN FOR A BLOWDOWN SUPERSONIC WIND TUNNEL BY USING GENETIC ALGORITHM [PDF]
مجله مدل سازی در مهندسی, 2017 Blowdown Supersonic Wind Tunnels (SWTs) are generally operated with a constant stagnation pressure in the settling chamber, with control usually provided by one or more pressure regulators or control valves. In this paper, first, a Simulink block diagram
Mehradad Bazazzadeh +3 more
doaj +1 more source
Optimization of operating conditions in the steam turbine blade cascade using the black-box method
Propulsion and Power Research, 2023 Water droplets cause corrosion and erosion, condensation loss, and thermal efficiency reduction in low-pressure steam turbines. In this study, multi-objective optimization was carried out using the black-box method through the automatic linking of a ...
Vahid Sadrian +5 more
doaj +1 more source
Experimental Study on Critical Flow of Supercritical CO2 at Steady State and Model Verification
Yuanzineng kexue jishu, 2022 When the loss of coolant accident happens in a reactor, because of the high temperature and high pressure in the reactor and the low external pressure, the critical flow may occur at the break due to sharp depressurization and vaporization.
LI Weiqing;ZHANG Dongxu;ZHAO Minfu
doaj
Numerical Simulation of Nozzle Flow Field with Secondary Injection Thrust Vector Control
MATEC Web of Conferences, 2018 Numerical simulations are performed to characterize the secondary injection thrust vector control. For this objective the following measurements were taken: considering the flow to be compressible and turbulent using Realizable k-ε turbulence model ...
Noaman H.R. +2 more
doaj +1 more source
Impinging Performance of High-Pressure Water Jets Emitting from Different Nozzle Orifice Shapes
Geofluids, 2020 The impinging pressure of a water jet is a key factor in engineering applications, and the jet shape has a great influence on this pressure. In this paper, five different nozzle shapes were designed, and impacting tests were conducted based on a self ...
Fei Huang +3 more
doaj +1 more source
Journal of Marine Science and EngineeringRegular inspections and hull cleanings are essential to prevent bio-fouling on ships. However, traditional cleaning methods such as brush cleaning and high-pressure water-jet cleaning at docks are ineffective in cleaning niche areas like bow thrusters ...
Jaehyeon Ahn +6 more
doaj +1 more source
Analysis of flow-field in a dual mode ramjet combustor with boundary layer bleed in isolator
Propulsion and Power Research, 2021 A two-dimensional Reynolds averaged Navier Stokes (RANS) simulation of a dual mode ramjet (DMRJ) combustor is performed, modeling the University of Michigan dual-mode combustor experimental setup operating in reacting mode with different equivalence ...
Nishanth Thillai +3 more
doaj +1 more source
Research on flow field characteristic of close-coupled gas atomizing nozzles
Fenmo yejin jishuThe atomization nozzle is the core component for the metal powder preparation by close-coupled gas atomization method. The pressure at the tip of the melt delivery tube and the stagnation point is very important for the smooth outflow of the molten metal
BAN Wei +4 more
doaj +1 more source