Results 101 to 110 of about 1,911,696 (350)
Microstructural characterization of AISI 431 martensitic stainless steel laser-deposited coatings [PDF]
, 2011 High cooling rates during laser cladding of stainless steels may alter the microstructure and phase constitution of the claddings and consequently change their functional properties.
A Zambon +22 more
core +3 more sources
Numerical Modeling of Tank Cars Carrying Hazardous Materials With and Without Composite Metal Foam
Advanced Engineering Materials, EarlyView.Large‐scale puncture models consisting of hazardous materials (HAZMATs) tank car with protective steel–steel composite metal foam (S–S CMF) are solved numerically. Tank car plate with added 10.91–13.33 mm thick S–S CMF layer does not puncture. Protective S–S CMF absorbs impact energy, reduces plate deformation, and prevents shear bands formation ...
Aman Kaushik, Afsaneh Rabiei
wiley +1 more source
Advanced Engineering Materials, EarlyView.Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser +4 more
wiley +1 more source
Materials & Design (1980-2015), 2019 The role of the inert gas during laser powder bed fusion (L-PBF) is to remove the process by-products and the air that is initially present in the process chamber. On this purpose, different gas supply options are available. The effect of the process gas
C. Pauzon +3 more
semanticscholar +1 more source
Robust Spot Melting by 3D Spot Arrangements in Electron Beam Powder Bed Fusion
Advanced Engineering Materials, EarlyView.This work proposes an approach to replace separately melted contours for spot melting in electron beam powder fusion. Adapting the spot arrangements close to the contour combined with stacking yields a comparable surface quality without the inherent challenges of separate contours, as demonstrated, by electron optical images and roughness measurements.
Tobias Kupfer +4 more
wiley +1 more source
Behaviour of stainless steel beam-to-column joints — Part 1: Experimental investigation
Journal of constructional steel research, 2019 Research on stainless steel structures has primarily focused on the structural response of individual members, whilst the response of joints has received far less attention to date.
Mohamed Elflah +3 more
semanticscholar +1 more source
Microstructure Design of Steel‐Spinel Composites via Spark Plasma Sintering Process
Advanced Engineering Materials, EarlyView.This study illustrates how spark plasma sintering at reduced oxygen partial pressure enables controlled formation of steel‐spinel composites through tailored redox reactions and cation exchange. Comparison of the MgO–Fe2O3, steel–(MgO+Cr2O3), and steel–(MgO+Fe2O3) systems shows how oxygen activity and interface chemistry govern spinel formation, phase ...
Mahnaz Mehdizadehlima +4 more
wiley +1 more source
Comparison of release torques of tightened bolts in vacuum and air [PDF]
, 1970 Various combinations of stainless steel, mild steel, and aluminum bolt-nut couples are tightened to 60 lb-ft in partial vacuum and in air. Results are given for tests with and without two lubricants /a fluorosilicone and a sodium silicate bonded dry-film/
Demorest, K. E.
core +1 more source
Ultra-high strength martensitic 420 stainless steel with high ductility
Additive Manufacturing, 2019 Martensitic 420 stainless steel was successfully fabricated by Selective laser melting (SLM) with >99% relative density and high mechanical strength of 1670 MPa, yield strength of 600 MPa and elongation of 3.5%.
Kamran Saeidi +6 more
semanticscholar +1 more source
Production of MgO/TiC Composites From MgO‐C Recyclates Using Spark Plasma Sintering
Advanced Engineering Materials, EarlyView.Using the spark plasma sintering technique, MgO/TiC composites are manufactured from recycled MgO‐C refractories stemming from the steel production that were mixed with titanium powder. This article shows, how the size of the Ti grains and their distribution in the powder mixture affect the local carbon concentration in TiC.
Jiayan Yu +3 more
wiley +1 more source