Results 21 to 30 of about 1,060,535 (286)

Effect of heat treatment on the high temperature ductility of 00Cr24Ni13 austenitic stainless steel casting billets

工程科学学报, 2015
The effect of heat treatment on the high temperature ductility of 00Cr24Ni13 austenitic stainless steel casting billets was investigated by heat treatment experiment, therma-compression test and thermal tensile test.
SHU Wei, LI Jun, LIAN Xiao-jie, WANG Xue-min   +3 more
doaj   +1 more source

Biaxial experimental investigation on tensile deformation of copper-containing austenitic stainless steel under different strain conditions

Journal of Materials Research and Technology
To address the issues of insufficient emphasis on bidirectional loading, high experimental equipment costs, and scarce related data in traditional research, its paper proposes and adopts a sequential biaxial tensile simulation method based on stepwise ...
Juan Li, Tiantian Zhang, Yinbo Zhang, Ruiyang Wang, Guanghui Zhao, Yaohui Song   +5 more
doaj   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Shear Behavior of Stainless Steel Girders with Corrugated Webs [PDF]

, 2022
This paper reports experimental and finite element investigations conducted to assess the shear strength of corrugated web girders in stainless steel. The steel under consideration is LDX 2101.
Al-Emrani, Mohammad, Flansbjer, Mathias, Amani, Mozhdeh   +2 more
core   +2 more sources

Synergistic improvement of corrosion‐strength of Mg‐Zn‐Ca‐Sn dilute alloys by adjusting the Sn/Ca atomic ratio

Journal of Magnesium and Alloys
This study systematically engineers a series of Mg-1.0Zn-xCa-ySn alloys (ZXT-series) by systematically varying Sn/Ca atomic ratios (1:4 in ZXT4, 1:8 in ZXT8, and 1:16 in ZXT16) to investigate its impact on microstructural evolution, mechanical properties,
Yun Feng, Muhammad Abubaker Khan, Han Wang, Didi Zhao, Shang Dai, Jingyuan Li   +5 more
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Stainless steel selection tool for water application: pitting engineering diagrams

Frontiers in Materials
Introduction: This work systematically investigates the effect of chloride level, temperature, and the water system’s oxidative power on the pitting corrosion performance of stainless steels in pH-neutral environments.Methods: Two test programs were set ...
Sukanya Hägg Mameng, Lena Wegrelius, Saman Hosseinpour   +2 more
doaj   +1 more source

Influence of TiO2 content on the physical properties of the CaF2—Al2O3-CaO—MgO—TiO2 five yuan electroslag remelting system

工程科学学报, 2018
The addition of Ti O2during the electroslag remelting (ESR) of Ti-containing superalloys can restrain the loss of Ti elements.The physical properties of the slag system are related to the smooth operation of smelting and the excellent quality of products.
SHI Shuai, GENG Xin, JIANG Zhou-hua, LI Hua-bing, XU Fang-hong, WANG Li-xin   +5 more
doaj   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Effect of drawing and annealing on the microstructure and mechanical properties of 304 austenitic stainless steel wire

Materials Research Express, 2021
Plastic deformation at room temperature, and the proceeding heat treatments, are important processes for optimizing the microstructure and mechanical properties of austenitic stainless steel. The microstructure and mechanical properties of cold-drawn 304
Qinhua Xu, Jianxin Zhu, Yong Zong, Lihua Liu, Xiaoyong Zhu, Fuen Zhang, Baifeng Luan   +6 more
doaj   +1 more source