Results 91 to 100 of about 24,125 (308)
Influence of grain size and niobium content on the creep resistance of ferritic stainless steels
, 2008 Includes abstract.Includes bibliographical references (leaves 98-102).Type 441 ferritic stainless steel is used for the production of catalytic converter housings.
Cain, Victoria
core
Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application
Advanced Engineering Materials, EarlyView.N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang +4 more
wiley +1 more source
Mechanical and thermal induced phase transformations in superduplex stainless steel
, 2000 The aim of this work is to study the microstructural changes in SAF 2507 type superduplex stainless steel due to heat treatments and mechanical fatigue process.
Dobránszky, János +2 more
core
Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading
Advanced Engineering Materials, EarlyView.This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev +2 more
wiley +1 more source
Experimental and numerical analysis on the martensitic transformation in AISI 304 steel sheets subjected to perforation by conical and hemispherical projectiles [PDF]
, 2013 Lien vers la version éditeur: http://www.sciencedirect.com/science/article/pii/S0020768312004039In this work, an experimental and numerical analysis of the martensitic transformation in AISI 304 steel sheets subjected to perforation by conical and ...
Rodríguez-Martínez, José Antonio +10 more
core +1 more source
Advanced Engineering Materials, EarlyView.Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş +2 more
wiley +1 more source
Application Prospect and Effect of Rare Earth Elements in Ferritic Stainless Steels
Teshugang, 2008 The anti-pitting corrosion,anti-stress corrosion and high temperature anti-oxidizing properties of ferritic stainless steels(11%～30%Cr)are better than that of austenitic stainless,but normal feritic stainless steels have higher ...
李亚波, 王福明, 朱宝晶
doaj
24 pages, contribution to the CAS - CERN Accelerator School: Mechanical & Materials Engineering for Particle Accelerators and Detectors, 2-15 June 2024, Sint-Michielsgestel ...
openaire +2 more sources
Enhanced radiopacity austenitic stainless steel foil [PDF]
, 2007 Austenitic stainless steel designed for implant applications is used to fabricate balloon expandable coronary stents. The alloy was not designed for this purpose but has been found to work well except for relatively low radiopacity in the energy range ...
Craig, Charles Horace
core
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source