Results 141 to 150 of about 1,494,649 (328)

3D Printed Photon Shield Assembly for Low‐Noise Visual Stimulation During Two‐Photon Imaging in Mice

Advanced Materials Technologies, EarlyView.
We present the Photon Shield, an open‐hardware system for low‐noise two‐photon calcium imaging during visual stimulation in mice. Combining a 3D‐printed headplate and rail‐mounted shield substantially reduces stray‐light contamination, as quantitatively verified. Functional validation confirms reliable cortical responses. Open design files enable broad
Gergely Katona, Andrea Slézia, András Dávid, Ábel Petik, Dániel Hillier, István Ulbert, Attila Kaszás   +6 more
wiley   +1 more source

Kinetics of Intermetallic Phase Precipitation in Manual Metal Arc Welded Duplex Stainless Steels. [PDF]

Materials (Basel), 2023
Orłowska M, Pańcikiewicz K, Świerczyńska A, Landowski M.   +3 more
europepmc   +1 more source

Spatially Configurable Conformal Sensor Integration on an Ultra‐Fine Metallic Needle for Minimally Invasive Deep‐Tissue Oxygen Monitoring

Advanced Materials Technologies, EarlyView.
A multi‐point oxygen‐sensing ultra‐fine needle (MO‐UFN) is developed by conformally integrating a lithographically patterned flexible electrochemical sensor array onto a clinical acupuncture needle. The platform preserves an approximately 0.3 mm diameter while enabling spatially resolved oxygen profiling along the insertion pathway.
Yeju Seo, Jaeho Park, Yongrok Jeong, Ji‐Hwan Ha, Junseong Ahn, Jimin Gu, Su A Park, Ilwoo Jun, Kichul Lee, Inkyu Park   +9 more
wiley   +1 more source

Copper Electroplated TPMS Polymer Lattices for Lightweight Absorption Dominant Electromagnetic Interference Shielding

Advanced Materials Technologies, EarlyView.
Copper electroplating transforms lightweight 3D‐printed TPMS polymer lattices into effective electromagnetic shields. Topology, relative density, and conductive seed layer continuity govern copper penetration, electrical resistance, and attenuation. SEA consistently exceeds SER, while 35% RD Diamond lattice gives the best performance, reaching 48.72 dB
Aman Al Khatib, Fares AlAwwa, Naod Mogos, Abdallah Kamal, Kin Liao, Marwan El Rich, Wael Zaki   +6 more
wiley   +1 more source

Synergistic Interfacial Regulation by Nano‐TiO2 and Carboxylated Cellulose Nanofibers for Multiscale Surface Stabilization of Cementitious Composites

Advanced Materials Technologies, EarlyView.
Nano‐TiO2 and carboxylated cellulose nanofibers jointly regulate hydration‐product distribution in cementitious composites. Improved microstructural continuity and refined pore structure accompany enhanced strength and surface stability without a substantial increase in overall hydration.
Kailun Chen, Peifeng Wu, Jason Scott, Fulin Qu, Caiyu Zhao, Zhaocheng Li, Zi Gu, Dewei Chu, Wengui Li   +8 more
wiley   +1 more source

Development of a Multi-technique Characterization Portfolio for Stainless Steels Exposed to Magnox Reprocessing Liquors. [PDF]

ACS Omega, 2023
Barton DNT, Denman AE, Grebennikova T, Carey T, Engelberg DL, Sharrad CA.   +5 more
europepmc   +1 more source

3D‐Printed Actuator Powered by Liquid Crystal Elastomer Muscles at the Water–Air Interface

Advanced Materials Technologies, EarlyView.
Soft robots for unstructured environments require responsive, durable actuators. Liquid crystal elastomers (LCEs) provide large reversible deformations under thermal or optical stimuli. Direct ink writing enables fabrication of LCE actuators integrated with silicone, with mesogen chemistry and oligomers optimized for printable inks.
Cecilie Ryberg, Stefan Pendlmayr, Jan Skov Pedersen, Jens Vinge Nygaard, Jan P. F. Lagerwall, Brigitte Städler   +5 more
wiley   +1 more source

Deformation characteristics of stainless steels

, 2005
This thesis describes the results of a theoretical and experimental investigation into the deformation characteristics of stainless steels. The title of the chapters is as follows; A new type of forming limit diagram for use with meta-stable ...
Andersson, Roger
core   +1 more source

Research Progress on Defect Behavior, Microstructure, and Service Performance of Additively Manufactured Austenitic Stainless Steels. [PDF]

Materials (Basel)
Liu K, Dong H, Zhang L.
europepmc   +1 more source

Kinetics of Nickel Diffusion into Austenitic Stainless Steels AISI 304 and 316L and Calculation of Diffusion Coefficients. [PDF]

Materials (Basel), 2023
Bukovská Š, Moravec J, Švec M.
europepmc   +1 more source