Results 61 to 70 of about 1,494,649 (328)
Advanced Engineering Materials, EarlyView.This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin +12 more
wiley +1 more source
HARDNESS OF NITRIDED LAYERS TREATED BY PLASMA NITRIDING
Acta Polytechnica CTU Proceedings, 2020 Stainless steels, particularly the austenitic stainless grades are widely used in many industries due to good corrosion resistance, but very poor mechanical properties as surface hardness and wear resistance limit its possible use.
Zdeněk Joska +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt +4 more
wiley +1 more source
Composition equivalents of stainless steels understood via gamma stabilizing efficiency
Scientific Reports, 2021 The phase-type of a stainless steel is generally predicted by equivalent equations in terms of a major austenitic (γ) or ferritic (α) stabilizer Ni or Cr.
Shuqi Zhang +3 more
doaj +1 more source
, 2018 The corrosion resistance of austenitic stainless steels AISI 316L, AISI 904L and Sanicro 28 and duplex stainless steels SAF 2205, SAF 2507 and SAF 2707, was studied at 40 and 60 °C in a strong acid mixture containing tartaric acid saturated solution, H 2
T. Bellezze +3 more
semanticscholar +1 more source
Electrodeposition in Structural Lattices of Variable Architectures
Advanced Engineering Materials, EarlyView.Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon +3 more
wiley +1 more source
Egyptian Journal of Petroleum, 2015 In this study, the effect of solution pH on the electrochemical behaviour of AISI 304 austenitic and AISI 430 ferritic stainless steels at open circuit potential (OCP) in concentrated acidic solutions was studied.
A. Fattah-alhosseini, S. Vafaeian
doaj +1 more source
Advanced Engineering Materials, EarlyView.Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika +5 more
wiley +1 more source
Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel
Advanced Engineering Materials, EarlyView.Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe +9 more
wiley +1 more source
Progress in Grades and Refining Technology of Ultra Purity Ferritic Stainless Steels
Teshugang, 2006 The(C+N)content in ultra purity ferritic stainless steels is ≤150×10-⁶,its corrosion resistance, weldability and toughness are obviously higher than that of common ferritic stainless steels.
游香米, 姜周华, 李花兵
doaj