Results 51 to 60 of about 531,907 (293)
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm +3 more
wiley +1 more source
Due to the complex mechanical structure and control process of escalator emergency braking systems (EEBS), traditional hazard analysis based on the event chain model have limitations in exploring component interaction failure in such a complex social ...
Zitong Zhou +3 more
doaj +1 more source
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source
Strategies to Increase Food Stamp Participation [PDF]
Discusses the benefits, for both individuals and states, of boosting participation in food and nutrition programs. Recommends strategies and best practices to expand participation while lowering costs, such as coordinating efforts with other ...
April Kaplan
core
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source
Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler +9 more
wiley +1 more source
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source
A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain +7 more
wiley +1 more source
Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories
Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov +6 more
wiley +1 more source

