Results 241 to 250 of about 254,559 (302)

Multiscale Modeling of Process‐Induced Defects in Fused Filament Fabrication‐Printed Materials

Advanced Engineering Materials, EarlyView.
This study presents a predictive multiscale modeling tool for defect analysis of fused filament fabricated‐printed materials and their performance prediction using a mechanistic data science‐based reduced‐order modeling approach. Process‐induced defects are inherent to additively manufactured parts and significantly influence the performance of printed
Satyajit Mojumder, Derick Suarez, Trevor Abbott, Wing Kam Liu   +3 more
wiley   +1 more source

Quantitative 18F-AV1451 brain tau PET imaging in cognitively normal older adults, mild cognitive impairment, and Alzheimer\u27s disease patients [PDF]

, 2019
Alzheimer\u27s Disease Neuroimaging Initiative,, Ha, Lingxia, Liu, Min, Zhao, Qian, Zhou, Yun   +4 more
core   +1 more source

Effect of Water Aging on the Mechanical Properties of Hybrid Carbon/Aramid Reinforced Thermoplastic Composites

Advanced Engineering Materials, EarlyView.
This study investigates the mechanical properties of Carbon/Aramid intraply hybrid fiber‐reinforced Elium composites under 6 months of water aging. After aging, flexural strength decreases by 25.89%, tensile strength by 4.40%, and fracture toughness by 21.56%.
Muhammed Huseyin Guzel, Gurol Onal
wiley   +1 more source

3D‐Printed Architected Material for the Generation of Foam‐Based Protective Equipment

Advanced Engineering Materials, EarlyView.
This study investigates 3D‐printed architected structures as alternatives to traditional foams in protective gear. It focuses on customizing impact strength and damping through design and manufacturing integration. Testing shows these structures outperform conventional foams, offering enhanced customizability, lower weight, and tunable performance ...
Ali Zolfagharian, Gerard Bel Català, Daniel Saakes, Bernard Rolfe, Ian Gibson, Mehrshad Mehrpouya   +5 more
wiley   +1 more source

Quality Enhancement of Laser Powder‐Bed Fusion Parts by Acoustically Assisted Additive Manufacturing by Laser Powder‐Bed Fusion and its Application to Lattice Structures

Advanced Engineering Materials, EarlyView.
Additive manufacturing technologies like laser powder‐bed fusion offer great design freedom and individualization of products down to a batch size of one. However, parts fabricated with this technology suffer from poor quality. Acoustic assistance during the build process can minimize these drawbacks.
Oliver Maurer, Dirk Bähre
wiley   +1 more source

Mechanical Behavior and Microstructural Changes Associated with Tensile Deformation above the Martensite Start Temperature during Quenching and Subsequent Partitioning of a Low‐Alloy 37SiB6 Steel

Advanced Engineering Materials, EarlyView.
A new experimental setup, incorporating digital image correlation and infrared thermography in combination with inductive‐conductive heating for precise temperature control, is used to analyze the mechanical behavior and microstructural changes of sheet metal under complex thermomechanical test conditions that represent quench and partitioning ...
Christian Illgen, Benjamin Bohne, Sven Winter, Marcus Böhme, Martin F.-X. Wagner   +4 more
wiley   +1 more source

Vacuum‐Formed Composites Based on a Polyolefin and a High Content of Biomass‐Waste Fillers

Advanced Engineering Materials, EarlyView.
It is shown here that by the use of a very ductile polymer matrix, it is possible to vacuum‐form products that contain up to 25% of hard biofillers with still ductile properties. The results are promising and opens up for the use of engineered biocomposites derived from industrial side‐stream biofillers in vacuum‐formed products. A strategy to increase
Susanna K. Källbom, Tuomo P. Kainulainen, Xin‐Feng Wei, Antonio J. Capezza, Daniel Helgesson, Richard T. Olsson, Mikael S. Hedenqvist   +6 more
wiley   +1 more source

Wafer Bonding Technologies for Microelectromechanical Systems and 3D ICs: Advances, Challenges, and Trends

Advanced Engineering Materials, EarlyView.
This review explores wafer bonding technologies, covering wafer preparation, activation methods, and bonding mechanisms. It compares direct and indirect bonding, highlights recent advancements and future trends, and examines applications in 3D integration and packaging.
Abdul Ahad Khan, Tuan‐Khoa Nguyen, Quang Thang Trinh, Nam‐Trung Nguyen, Dzung Viet Dao, Yong Zhu   +5 more
wiley   +1 more source

New Developments in the Field of Production and Application of Multi‐Material Wire Arc Additive Manufacturing Components: A Review

Advanced Engineering Materials, EarlyView.
The utilization of direct energy deposition (DED)‐arc additive manufacturing processes in industrial applications is increasing, and these processes have the potential for multi‐material applications. This work provides a overview of the state of research in DED‐arc made functional graded structures, to establish a link to potential industrial ...
Kai Treutler, Volker Wesling
wiley   +1 more source

Investigation of Oxide Dispersion Strengthening Effect on the Strength of Diffusion‐Bonded AISI304 Parts

Advanced Engineering Materials, EarlyView.
Experiments for reinforcing the diffusion bonding plane by the oxide dispersion strengthening effect are presented. Small ceramic particles (0.5 and 50 μm, respectively) are incorporated. Furthermore, ceramic particles help to penetrate stable passivation layers, enabling atomic diffusion across bonding planes. Since a ceramic–metallic interface cannot
Thomas Gietzelt, Mario Walter, Volker Toth, Florian Messerschmidt, Melina Blem   +4 more
wiley   +1 more source