Results 91 to 100 of about 132,283 (262)

Height and sex estimation using percutaneous humeral length among Ghanaians

Forensic Science International: Reports
Introduction: Humerus is a long bone that contributes significantly to the total height of an individual. It is sexually dimorphic and is a well-preserved bone postmortem.
Joshua Tetteh, Thomas Diby, Chrissie Stansie Abaidoo, Joseph Yorke, Juliet Robertson, James Nketsiah   +5 more
doaj   +1 more source

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Stand top heigh estimation from “plot top height”. Advantages versus Assman top height

Forest Systems, 1999
Assman top height is a parameter whose measurement or estimation is tiring in the practice and presents some inconveniences from a stadistical point of view which lessens efectiviness. Considering it’s a dasometric parameter widely used in Spain and with important silvicultural implications, we consider it suitable to look for alternatives which solve ...
openaire   +3 more sources

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Evaluation of Modulus of Elasticity in Standing Trees and Sawn Wood in Populous deltoids using Nondestructive Stress Wave Testing [PDF]

Iranian Journal of Wood and Paper Industries, 2014
The aim of this paper was to evaluate relationship between dynamic modulus of elasticity (MOEd) in healthy standing trees of Populus deltoides and static modulus of elasticity (MOEs) of sawn lumber from the same standing trees, using nondestructive ...
Mehrab Madhoushi, Soheila Daneshvar
doaj  

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Laser Metal Deposition of Aluminum Alloys 7075 and 5083 with the Addition of Volatile Alloying Elements through Powder Blending

Advanced Engineering Materials, EarlyView.
This study investigates laser metal deposition of aluminum alloys EN AW‐7075 and EN AW‐5083, using powder blending to compensate zinc and magnesium evaporation. In situ alloying and ex situ alloying with ZnAl12 and AZ91 preserve near‐standard compositions and improve mechanical properties.
Finn Bendixen, Anastasiya Toenjes, Annika Bohlen, Thomas Seefeld   +3 more
wiley   +1 more source

PBF‐LB/M of Ti‐6Al‐4V: High‐Pressure Solution Treatment and Aging for Applications in a Sustainable Aerospace

Advanced Engineering Materials, EarlyView.
Additive manufacturing (AM) allows great geometric freedom for lightweight components. As parts are progressively optimized exploiting potentials in AM leading in smaller material cross sections, high pressure solution treating and aging (STA) treatments show an enormous potential for strongly improving material properties.
Mika León Altmann, Andre Danzig, Freerk Syassen, Rainer Fechte‐Heinen, Anastasiya Toenjes   +4 more
wiley   +1 more source