Results 81 to 90 of about 425,220 (296)

Determination of melon seed physical parameters and calibration of discrete element simulation parameters.

PLoS ONE
To improve the accuracy of the Hami melon discrete element model, the parameters of the Hami melon seed discrete element model were calibrated by combining practical experiments and simulation tests. The basic physical parameters of Hami melon seeds were
Yuan Wan, Bowen Zhang, Qinghui Lai, Yan Gong, Yu Qingxu, Xiao Chen   +5 more
doaj   +1 more source

Loaded tooth contact analysis of intersected beveloid and cylindrical involute gear pair with small shaft angle

Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2018
A working pitch cone based geometry design approach for the intersected beveloid and cylindrical involute gear pair with small shaft angle was proposed. The cutter and geometry design parameters can be determined by the proposed method.
Chaosheng SONG, Yao ZHOU, Caichao ZHU, Gaoxiang NI, Siyuan LIU   +4 more
doaj   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Pest risk analysis for Bactrocera invadens : Guidelines on Pest Risk Analysis [PDF]

, 2010
Stripping related moisture damage has been recognized as one of the major pavement distresses since the early 1990s. The main objective of this study is to establish an effective test protocol to quantify moisture susceptibility of asphalt pavements.
Guitian Castrillon, José Maria, Catalan Ruescas, Diana, De Meyer, Marc, Zulma, Denis Félicité, Guichard, Catherine, MacLeod, Alan, Plumelle, Frédéric, Quilici, Serge, Üstün, Nursen, Vayssières, Jean-François   +9 more
core   +2 more sources

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

Calibration of force sensor mounted in tire tread block under rolling contact condition

Polymer Testing
This study investigates a sensor calibration method for accurately measuring the three-axis contact forces of a single tread block using sensor-equipped tires.
Koga Ishido, Masami Matsubara, Takayuki Toyoshima, Tomonori Sakai, Akira Shibuya, Hiroshi Tachiya, Masahiro Higuchi   +6 more
doaj   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source