Results 141 to 150 of about 1,771,897 (325)

An Inkjet‐Printed Platinum‐Based Temperature Sensing Element on Polyimide Substrates

Advanced Engineering Materials, EarlyView.
An inkjet‐printed, meander‐structured, nanoparticle platinum‐based resistive temperature sensors on polyimide substrates are demonstrated as proof‐of‐concept. Optimized sintering at 250°C enables stable conductive structures. The Pt100‐ and Pt1000‐type sensors exhibit linear resistance–temperature characteristics with stable TCR in the 20°C–80°C range,
Shawon Alam, Thomas Kister, Alexander Scholz, Sophie Sauva, Makara Lay, Tobias Kraus, Jasmin Aghassi‐Hagmann   +6 more
wiley   +1 more source

A hyper-redundant manipulator gluing system under multiple constraints

Advances in Mechanical Engineering
There are many narrow gluing operation scenarios, such as engine components, turbine blades, and combustion chambers in the aerospace engineering. Traditional six-axis manipulator cannot enter such narrow spaces due to size constraints.
Dongjie Zhao, Aoshun Zhang, YanBin Yao, Mingrui Luo, En Li, Jing-Shan Zhao   +5 more
doaj   +1 more source

Computational analysis of the SSME fuel preburner flow [PDF]

A computational fluid dynamics model which simulates the steady state operation of the SSME fuel preburner is developed. Specifically, the model will be used to quantify the flow factors which cause local hot spots in the fuel preburner in order to ...
Farmer, R. C., Wang, T. S.
core   +1 more source

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

In-situ analysis of hydrazine decomposition products [PDF]

A gas analyzer utilizing a nondispersive infrared (NDIR) detection system was used to monitor the ammonia and water vapor content of the products of a previously unused hydrazine gas generator.
Curran, Francis M., Whalen, Margaret V.
core   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Nitride‐Reinforced Metal Matrix Nanocomposite Powders Production by Plasma‐Assisted Thermochemical Treatment of Intermetallic Powders

Advanced Engineering Materials, EarlyView.
This study proposes a new methodology for producing metal matrix nanocomposites in the solid state. The process involves the plasma‐assisted thermochemical treatment of metallic alloy powders. As a proof‐of‐concept, TiN nanoparticles are synthesized directly on the surface of FeTi intermetallic powder particles, enabling the development of the ...
Deivison Daros Paim, Antônio Rogério de Souza, Tatiana Bendo, Aloisio Nelmo Klein, Rodrigo Perito Cardoso   +4 more
wiley   +1 more source

Transfer of Energy and Momentum Between Magnetoactive Surface Microstructure and a Solid Object

Advanced Engineering Materials, EarlyView.
We demonstrate that magnetoactive multilamellar arrays subjected to a rotating magnetic field can function as platforms for controlled transport of physical objects. Through systematic experimental investigation, we elucidate the underlying physical mechanisms determining the upper limit of the achievable transportation speed in such magnetic “conveyor‐
Arne Geldof, Jan Kopačin, Izidor Straus, Raphael Kriegl, Gaia Kravanja, Luka Hribar, Matija Jezeršek, Mikhail Shamonin, Gašper Kokot, Irena Drevenšek‐Olenik   +9 more
wiley   +1 more source