Results 151 to 160 of about 440,835 (294)

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Incorporation of Selenium into Sol–Gel‐Derived Bioactive Glass: Influence on Glass Structure, Bioactivity, and its Selective Cytotoxicity

Advanced Engineering Materials, EarlyView.
Selenium was incorporated into a sol–gel‐derived bioactive glass to enable sustained therapeutic ion release. The selenium‐containing glass preserved bioactivity while selectively inducing cytotoxicity in osteosarcoma cells and maintaining osteoblastic viability.
Breno Rocha Barrioni, Thalita Marcolan Valverde, Talita Martins, Guilherme Mattos Jardim Costa, Alfredo Miranda de Goes, Marcello Rosa Dumont, Eduardo Henrique Martins Nunes, Marivalda de Magalhães Pereira   +7 more
wiley   +1 more source

Steady-state analysis of full-bridge series resonant converter with phase-shift and frequency control [PDF]

, 2010
Aboushady, Ahmed, Ahmed, Khaled, Finney, Stephen, Williams, Barry   +3 more
core   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

Robust speed control of permanent magnet synchronous motors using model predictive and sliding mode strategies. [PDF]

PLoS One
Meawad M, Ahmed AA, Abdelkader MI, Dessouky YG.   +3 more
europepmc   +1 more source

OPTIMIZATION OF QUASI-STEADY-STATE OPERATING MODES OF SYNCHRONOUS JET MOTORS WITH PERMANENT MAGNETS FOR ELECTRIC BUSES

Енергозбереження. Енергетика. Енергоаудит.
Abstract. The work created an algorithm for determining the optimal control parameters of a traction synchronous jet motor with permanent magnets based on the specified power supply conditions and rotation frequency. The dependences of the drive efficiency, the traction motor efficiency, the load angle and the modulation coefficient for their optimal ...
openaire   +2 more sources

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Performance-driven switched reluctance motor drive using multiport cascaded converter and advanced direct torque control scheme. [PDF]

Sci Rep
Deepak M, Santhakumar K, Sathiyasekar K, Chokkalingam B, Padmanaban S.   +4 more
europepmc   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source