Results 151 to 160 of about 3,796,291 (302)

The impact of steel protection in industrialized countries on Brazil's export capacity [PDF]

Since the beginning of the 1970s most industrialized countries have been facing serious structural adjustment problems in the steel sector, which can be attributed mainly to two reasons.
Amelung, Torsten
core  

Composition and Leaching Toxicity of Hydrochloric Acid Pickling Sludge Generated from the Hot-Dip Galvanized Steel Industry. [PDF]

ACS Omega, 2022
Xu Y, Zhang Y, Shu Y, Song H, Shu X, Ma Y, Hao L, Zhang X, Ren X, Wang Z, Zhang X.   +10 more
europepmc   +1 more source

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

Advanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul, Alexander Welle, Dirk Matthiessen, Michael Oehring, Fritz Appel, Florian Pyczak   +5 more
wiley   +1 more source

Reduction of CO₂ Emission from Off-Gases of Steel Industry by Dry Reforming of Methane. [PDF]

Angew Chem Int Ed Engl, 2021
Angeli SD, Gossler S, Lichtenberg S, Kass G, Agrawal AK, Valerius M, Kinzel KP, Deutschmann O.   +7 more
europepmc   +1 more source

Process Gas Transitions in the Steel Industry—Planning Corridors for Chemical Utilization [PDF]

Ömer Yildirim
openalex   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Techniques for In Situ Monitoring the Performance of Organic Coatings and Their Applicability to the Pre-Finished Steel Industry: A Review. [PDF]

Sensors (Basel), 2021
Savill T, Jewell E.
europepmc   +1 more source

Dynamic Capabilities for Sustainable Technologies in the Steel Industry: A Multiple Case Study [PDF]

Frida Betto, Rosanna Fornasiero, Andrea Zangiacomi, Markus Witthaut, Patrizia Garengo   +4 more
openalex   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Michael Steel (Junior) to Jane Steel (Sister) Enstone, Oxon

, 2016
This record was harvested from a previous catalogue system and will be withdrawn in 2025. Information in this record may be superseded or incomplete.
Steel Family
core