Results 121 to 130 of about 596,686 (360)
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
Long-term weathering effects on the thermal performance of the Lennox/Honeywell (liquid) solar collector [PDF]
The test procedures used and the results obtained during the evaluation test program of the Lennox/Honeywell double covered liquid solar collector. The tests were performed under simulated conditions, following long-term exposure to natural weathering ...
core +1 more source
Analisis Pembuatan Pipa Baja Sistem Dua Bagian Las Astm A139 Dengan Menggunakan Metoda Lsaw = Manufactur Analysis Dual Seam Weld Steel Pipe Astm A139 by Using Lsaw Methode [PDF]
, 2014 One of the main components of the manufacture of steel pipe is in the form of plate steel sheet, slab or hot roll coil, which of these materials may be made for various types of pipes, among others, seamless, Electric Wire Resistance, Spiral and ...
Karmiadji, D. W. (Djoko) +1 more
core
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Numerical Investigation of Longitudinal through Voids in Tunnel Secondary Lining Vaults and Steel Plate Strengthening. [PDF]
Materials (Basel), 2023 Shao S, Wu Y, Fu H, Feng S, Zhang J.
europepmc +1 more source
Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)
Advanced Engineering Materials, EarlyView.Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho +8 more
wiley +1 more source
工程科学与技术This study conducts pseudo-static tests on two prefabricated exterior damping joints equipped with steel plate damper connection to investigate the effects of different energy dissipation mechanisms of the steel plate dampers on the mechanical behavior ...
Ruyue LIU +4 more
doaj
Teshugang, 2007 The effect of titanium content on mechanical properties of 14～20 mm hot rolled plate of Q345A steel (0.08~0. 10C,1.19～1.46Mn,0.017～0.029Nb,0.02～0.08Ti) has been studied.
刘丽霞, 王世俊, 周云, 彭军
doaj
PERENCANAAN GEDUNG PERKANTORAN/PERKULIAHAN UNIVERSITAS MUHAMMADIYAH MALANG DENGAN BALOK-LANTAI KOMPOSIT DAN KOLOM BAJA BERONGGA MENGACU "SPESIFICATION AISC-LRFD" [PDF]
, 2006 Composite Construction. Many structural systems that can not be easily categorized according to the material used. Composite beam system as we often encounter.
HAMID, ABDUL
core