Results 91 to 100 of about 1,466,204 (297)

Effects of Mg on Microstructure and Solidification of a Hypereutectic Zn–8 wt.%Al Alloy

open access: yesAdvanced Engineering Materials, EarlyView.
An appreciable set of results involving thermal data, microstructure, chemical composition, and microstructural growth laws is reported for ZnAlMg alloys. Such results demonstrate that ZnAlMg alloys have high potential for applications in automotive self‐lubricating components, batteries, and electrical systems.
Raí B. de Sousa   +6 more
wiley   +1 more source

Large deformations of thin plates subjected to impulsive loading [PDF]

open access: yes, 1987
Includes bibliographical references.The dynamic response of structures subjected to blast and impact loading has been obtained relatively simply using rigid-plastic or rigid-viscoplastic material idealisations.
Nurick, Gerald N
core   +1 more source

Experimental Investigation and FEM Modeling of Glued Timber Connections with Slotted-In Steel Plates

open access: yesSlovak Journal of Civil Engineering, 2019
The study is focused on the mechanical behavior and finite element method (FEM) modeling of glued timber dowel connections with slotted-in steel plates.
Shekhorkina Svitlana   +4 more
doaj   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

open access: yesAdvanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin   +12 more
wiley   +1 more source

Third International Conference on Advances in Steel Structures (2002)

open access: yes, 2002
Steel plates in double skin composite (DSC) panels may buckle locally between shear connectors when subjected to biaxial compression. The local and post-local buckling behaviour of biaxially compressed steel plates restrained by discrete stud shear ...
Bradford, Mark A.   +3 more
core  

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

open access: yesAdvanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt   +4 more
wiley   +1 more source

Microstructure‑Dependent Phase Transformations Under High‑Pressure Laser Heating in Additively Manufactured AlCrFe2Ni2

open access: yesAdvanced Engineering Materials, EarlyView.
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika   +5 more
wiley   +1 more source

An alternative design of steel-concrete-steel sandwich beam

open access: yes, 2010
A steel-concrete-steel sandwich beam represents a special form of sandwich structure. Originated in civil/structural engineering applications, it is now being developed for shipbuilding/offshore applications.
Leekitwattana, M.   +2 more
core   +1 more source

Steel specification comparisons Part 2: boiler and pressure vessel steel plates

open access: yes, 1980
7.50Available from British Library Lending Division - LD:84/33466(Steel) / BLDSC - British Library Document Supply CentreSIGLEGBUnited ...
British Steel Corporation, London (United Kingdom). Plates
core  

Influence of Particle Shape and Size in Copper‐Based Low‐Temperature Metallization Paste for Solar Cells

open access: yesAdvanced Engineering Materials, EarlyView.
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy