Results 1 to 10 of about 17,784 (265)
Enhancement of Damping Capbility of MnCu Alloy by High Magnetic Field
Metals, 2022 The directionally solidified MnCuNiFe alloy was prepared under high magnetic field. The microstructure, composition distribution, phase transformation behavior and damping capacity of the alloy were studied by means of metallographic microscope, scanning
Diwei Wang +5 more
doaj +1 more source
Non-wetting to Wetting Transition Temperatures of Liquid Tin on Surfaces of Different Steel Samples Corresponding to their Spontaneous Deoxidation [PDF]
Archives of Metallurgy and Materials, 2021 The goal of this paper is to measure the non-wetting to wetting transition temperatures of liquid tin on surfaces of different steel samples in vacuum with residual pressure of 10–8 bar.
D. Varanasi +4 more
doaj +1 more source
Surface Hardening Behavior of Advanced Gear Steel C61 by a Novel Solid-Solution Carburizing Process
Metals, 2022 During vacuum carburizing, coarse reticulated carbides tend to precipitate along grain boundaries due to high-carbon-potential conditions. This phenomenon is often one of the main factors in the failure of conventional gear steels. In this paper, a novel
Yanzhang Dai +6 more
doaj +1 more source
Numerical Simulation on Saffman Force Controlled Inclusions Removal during the ESR Process
Metals, 2020 Electroslag remelting (ESR) is an effective method for removing nonmetallic inclusions from steels or alloys. The main stage of inclusion removal during ESR is the aggregation of liquid metal film (LMF) to form droplets at the consumable electrode tip ...
Chuxiong Sun +8 more
doaj +1 more source
Journal of Materials Research and Technology, 2022 The novel processing concept of direct quenching and partitioning (DQ&P) has been explored with a medium-carbon (0.4 wt.% C) steel to evaluate and optimize the processing route for excellent property combinations.
Sumit Ghosh +7 more
doaj +1 more source
Journal of Materials Research and Technology, 2021 A new combination of factors enhancing the stabilization of austenite, including pre-existed austenite among quenched martensite, prior deformation, and partitioning at high temperatures is employed to create a multi-component refined microstructure in a
Saeed Sadeghpour +3 more
doaj +1 more source
Materials Research Express, 2023 In this study, systematic heat treatment routes including solution (980 °C to 1130 °C) and aging (675 °C to 775 °C) processes were used to tailor the microstructural evolution and mechanical performance of a Fe-Ni-Cr based austenitic alloy, strengthened ...
Jina Li +5 more
doaj +1 more source
Journal of Aeronautical Materials, 2022 In the process of directional solidification, the degree of element segregation can be changed by altering the drawing rate to affect the phase transformation behavior of the alloy.
WANG Diwei, NIU Hongkang, TIAN Qingchao
doaj +1 more source
Dynamic and high temperature mechanical behavior of GCr15SiMo steel
Cailiao gongcheng, 2022 The effect law of heat treatment process on the microstructure of GCr15SiMo steel was studied, and the dynamic and high temperature mechanical behavior of GCr15SiMo steel with different microstructure was analyzed by using Hopkinson rod and GNT100-2 high
YAN Yongming +4 more
doaj +1 more source
Effect of Thermomechanical Controlled Processing and Quenching & Tempering on the Structure and Properties of Bainite-Martensite Steels [PDF]
Archives of Metallurgy and Materials, 2020 In the present time, advanced high strength steel (AHSS) has secured a dominant place in the automobile sector due to its high strength and good toughness along with the reduced weight of car body which results in increased fuel efficiency, controlled ...
G. Mandal, S.K. Ghosh, S. Chatterjee
doaj +1 more source