Results 221 to 230 of about 1,340,740 (334)

The Nanoparticle Stability and Microstructural Evolution of 9Cr-ODS Steel Under Fe Ion Irradiation at Elevated Temperatures. [PDF]

Materials (Basel)
Wei Y, Qian W, Zheng P, Xu M, Zhang Y, Wang J, Huang J, Zhang J, Li B.   +8 more
europepmc   +1 more source

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

Experimental data on the generation of compressive residual stresses via shot peening and subsequent heat treatment in SAE 5160 and DIN 51CrV4 spring steels. [PDF]

Data Brief
Pereira Dos Santos M, Farias A, Bordinassi EC, Delijaicov S.   +3 more
europepmc   +1 more source

Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control

Advanced Engineering Materials, EarlyView.
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian, Frédéric Demoly, Mohammad Lakhi, Bernard Rolfe, Mahdi Bodaghi   +4 more
wiley   +1 more source

Evolution of Cluster Morphology and Its Impact on Dislocation Behavior in a Strip-Cast HSLA Steel. [PDF]

Materials (Basel)
Yu H, Huang Y, Lu J, Gao J, Zhao H, Wu H, Zhang C, Wang S, Mao X.   +8 more
europepmc   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Revealing the influence of Cr and Al additions on the corrosion of carbon steel in a supercritical CO₂-SO₂ environment. [PDF]

RSC Adv
Zhu R, Zhu J, Shi H, Xu L, Zhang Y, Yang Z, Liu Y, Li H.   +7 more
europepmc   +1 more source

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, EarlyView.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

Comparative Analysis of Microstructure and Properties of Wear-Resistant Structural Steels. [PDF]

Materials (Basel)
Lukšić H, Rodinger T, Rede V, Švagelj Z, Ćorić D.   +4 more
europepmc   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source