Results 191 to 200 of about 23,434 (253)

Development of a Gingiva Model With Periosteum for Dental Students Using 3D Printing Compared to Knowledge‐Related Models

European Journal of Dental Education, EarlyView.
ABSTRACT Introduction An adequate gingiva model for dental students has special requirements, such as strength, flexibility and a periosteum. As there is a lack of available models, the aim of this study was to develop a new and sufficient gingiva model that fits students' needs.
Katharina Schaffrath, Mark Ooms, Kristian Kniha, Anna Bock, Philipp Winnand, Nils Vohl, Frank Hölzle, Ali Modabber   +7 more
wiley   +1 more source

Effect of Support Spacing on the Region-Specific Dimensional Accuracy of 3D-Printed Dental Models. [PDF]

Materials (Basel)
Alpöz B, Akan B, Akan E.
europepmc   +1 more source

Comparative Evaluation of the Effect of Different Polishing Systems on Surface Roughness of Permanent 3D‐Printed Resins and a CAD/CAM Restorative Material

Journal of Esthetic and Restorative Dentistry, EarlyView.
ABSTRACT Objective This study evaluated the effects of polishing systems, staining solutions, and aging time on the surface roughness of Computer‐aided design and computer‐aided manufacturing (CAD/CAM) and three‐dimensional (3D)‐printed permanent restorative materials. Methods Three 3D‐printed resins (VarseoSmile Crown plus (VSC), Saremco PrintCrowntec
Nilay Bayraktar, Nurgül Çetin Tuncer, Çağatay Barutçugil   +2 more
wiley   +1 more source

Adhesion of Composite Resin to Additively Manufactured Zirconia Using a Self-Adhesive Resin Cement: Evaluation of Micro-Shear Bond Strength. [PDF]

Polymers (Basel)
Zhu Y, Qian C.
europepmc   +1 more source

How the Build Angle Affects the Marginal and Internal Fit of 3D Printed Definitive FPDs: An in Vitro Study

Journal of Esthetic and Restorative Dentistry, EarlyView.
ABSTRACT Statement of Problem Printing parameters may influence the fit of additively manufactured dental restorations. However, the effect of small incremental build angles on the marginal and internal fit of stereolithography (SLA)‐printed definitive 3‐unit fixed partial dentures (FPDs) has not been sufficiently investigated.
Bora Akat, Bahar Kavafoğlu Yilmaz, Fehmi Gönüldaş, Mert Ocak, Stephen F. Rosenstiel, Evşen Tamam   +5 more
wiley   +1 more source

Digital Versus Conventional Splints in Patients With Temporomandibular Disorders: A Systematic Review and Meta-Analysis of Randomized Controlled Trials. [PDF]

Cureus
Almansour FW, Alshammari K, Mohammed Alhajri D, Bader Alzamanan M, Hamed Alduaij F, Walled Abdullah K, Homoud Alnoumas M, Abdelaziz A.   +7 more
europepmc   +1 more source

Effect of Different Surface Treatments and Manufacturing Methods on the Shear Bond Strength of Repaired Resin‐Based Restorations

Journal of Esthetic and Restorative Dentistry, EarlyView.
ABSTRACT Objective The aim of this in vitro study was to evaluate the effects of different surface treatments on the shear bond strength of repaired milled and 3D‐printed resin restorations. Materials and Methods A total of 84 resin specimens (8 mm diameter, 5 mm height) fabricated using two different methods such as milling (Grandio Disc) and 3D ...
Berkman Albayrak, Sarp Kocaer, Sina Saygılı   +2 more
wiley   +1 more source

Computational Fluid Dynamics to Investigate the Possible Behavior of <i>Ercaicunia multinodosa</i> While Swimming Inverted on the Water Surface. [PDF]

Biology (Basel)
Li Y, Yang Z, Zhou Z.
europepmc   +1 more source

Marginal and Internal Adaptation of Crowns Fabricated on Models From Digital and Conventional Impressions: An In Vitro Study

Journal of Esthetic and Restorative Dentistry, EarlyView.
ABSTRACT Objective To evaluate the marginal and internal adaptation of monolithic crowns fabricated from lithium disilicate (LD), zirconia (Zr), and fiber‐reinforced composite (FRC) using five different model types derived from digital and conventional impressions.
Mohanad Shomal, Şafak Külünk, Seniha Kısakürek   +2 more
wiley   +1 more source

Fabrication and characterisation of Ti and DLC coatings on metamaterial-architecture-inspired 3D-printed polymer substrates. [PDF]

Int J Adv Manuf Technol
V-Niño ED, Endrino JL, Díaz Lantada A, Fernández Martínez I, Estupiñán Duran HA, Goel S.   +5 more
europepmc   +1 more source