Results 81 to 90 of about 5,572 (200)

Characteristics of A6061/(Glass Fibre + AL2O3 + SiC + B4C) Reinforced Hybrid Composite Prepared through STIR Casting

Advances in Materials Science and Engineering, 2019
In this article, A6061 and its reinforcement particles like aluminium oxide/glass fibres/SiCp/B4C (4% and 5%) with mixed composite and aluminium oxide/SiCp/B4C mixed without glass fibre composite are produced with different proportions using the stir ...
Subramani Nanjan, Ganesh Murali Janakiram   +1 more
doaj   +1 more source

Characterization of mechanical and wear properties of aluminium based composites reinforced with quarry dust and silicon carbide

Ain Shams Engineering Journal, 2018
The mechanical and wear behavior of quarry dust (QD) and silicon carbide (SiC) particle reinforced Aluminium based composites was investigated. QD mixed with SiC in varied weight ratios, were used to produce 8 wt% reinforced Al-Mg-Si based composites ...
Kenneth Kanayo Alaneme, Bethel Jeremiah Bamike   +1 more
doaj   +1 more source

Investigation of the Mechanical Behavior of Synthesized Al6061/TiO₂ Microcomposites Using an Innovative Stir Casting Method. [PDF]

Nanomaterials (Basel), 2022
Badran AH, Alamro T, Bazuhair RW, El-Mawla AAG, El-Adben SZ, Fouly A.   +5 more
europepmc   +1 more source

Microstructural and mechanical characterization of AA6082/SiC/Al2O3 hybrid nanocomposite fabricated by ultrasonic-assisted and vacuum die stir casting

Discover Materials
The utilization of aluminium alloys has increased rapidly in past decades due to the increasing demand for lightweight and high-performance materials. Among the popular aluminium alloys, AA6082 is widely favoured for its excellent combination of strength,
Anasmon Koderi Valappil, Ansar Kareem, Jaber Abu Qudeiri, Asarudheen Abdudeen, Abdul Kareem Kalathil Soopy   +4 more
doaj   +1 more source

A Contemporary Review of Aluminium MMC Developed through Stir-Casting Route. [PDF]

Materials (Basel), 2021
Yadav P, Ranjan A, Kumar H, Mishra A, Yoon J.   +4 more
europepmc   +1 more source

Dry Sliding Wear Studies on Sillimanite and B₄C Reinforced Aluminium Hybrid Composites Fabricated by Vacuum Assisted Stir Casting Process. [PDF]

Materials (Basel), 2022
Pethuraj M, Uthayakumar M, Rajesh S, Abdul Majid MS, Rajakarunakaran S, Niemczewska-Wójcik M.   +5 more
europepmc   +1 more source

Design and Fabrication of Bottom Pouring Type Stir Casting Furnace With Carrier Gas

, 2019
Among the available processing techniques of composite materials, stir casting is an attractive processing method for producing MMCs. It is relatively inexpensive and offers a wide selection of materials and processing conditions.
Ashok Kumar M S, Mohith P, Pramod B R, Roopesh S, Nanjesh Kumar G C   +4 more
core   +1 more source

Evolution of Microstructure and Mechanical Properties of LM25-HEA Composite Processed through Stir Casting with a Bottom Pouring System. [PDF]

Materials (Basel), 2021
Chinababu M, Naga Krishna N, Sivaprasad K, Prashanth KG, Bhaskara Rao E.   +4 more
europepmc   +1 more source

Optimization of stir casting method of aluminum matrix composite (AMC) for the hardness properties by using Taguchi method

, 2017
Aluminum matrix composite (AMC) was fabricated using stir casting with fly ash and SiC as reinforcing materials. In this work, Taguchi optimization technique was utilized to analyze the significant contributions of stir casting parameters on the hardness
Azhanie Sardangi
core  

Sedimentation in the A356-Al2O3 Stirred Cast

MATERIAIS 2022, 2022
Omid Emadinia, Rui Madureira, Rui Soares, Helder Nunes, Inês Frada, Vitor Anjos, Carlos Silva Ribeiro, Rui Neto, Ana Reis, Manuel Vieira   +9 more
openaire   +1 more source