Results 211 to 220 of about 708,199 (311)

An enhanced Bayesian approach for damage identification utilizing prior knowledge from refined elemental modal strain energy ratios. [PDF]

Sci Rep
Chen L, Chen H, Liu LL.
europepmc   +1 more source

Global Longitudinal Active Strain Energy Density (GLASED): A Powerful Prognostic Marker in a Community-Based Cohort

, 2023
Aung N, MacIver DH, Zhang H, Chadalavada S, Petersen SE.   +4 more
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Effect of true triaxial principal stress unloading rate on strain energy density of sandstone. [PDF]

Sci Rep
Liu Z, Zhao G, Meng X, Gu Q.
europepmc   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Global longitudinal active strain energy density (GLASED): a powerful prognostic marker in a community-based cohort. [PDF]

Eur Heart J Cardiovasc Imaging
Aung N, MacIver DH, Zhang H, Chadalavada S, Petersen SE.   +4 more
europepmc   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

A Master Curve for Fatigue Design of Notched Nodular Cast Iron Components Based on the Local Averaged Strain Energy Density. [PDF]

Materials (Basel)
Pelizzari J, Campagnolo A, Dengo C, Meneghetti G.   +3 more
europepmc   +1 more source

Experimental Validation of an ITAP Numerical Model and the Effect of Implant Stem Stiffness on Bone Strain Energy. [PDF]

Ann Biomed Eng, 2020
Ahmed K, Greene RJ, Aston W, Briggs T, Pendegrass C, Moazen M, Blunn G.   +6 more
europepmc   +1 more source