Results 131 to 140 of about 153,531 (299)

Phenomenological and Physically Based Modeling of Flow Stress and Strengthening Mechanism of Inconel 718

Advanced Engineering Materials, EarlyView.
Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein, Oliver Schenk, Christoph Broeckmann   +2 more
wiley   +1 more source

Strain-hardening resilience via the cooperation of geometrically necessary dislocations and deformation twins in a strong and ductile lightweight high-entropy steel

Materials & Design
In the net-zero era, the burgeoning demands within engineering applications require materials that are not only lighter and stronger but also ductile.
Yi-Hsuan Sun, Shi-Wei Chen, Zen-Hao Lai, Shao-Lun Lu, Yi-Ting Lin, Jui-Fan Tu, Hung-Wei Yen   +6 more
doaj   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Experimental study on low cycle fatigue behavior of TWIP steel under cyclic shear loading condition

Journal of Materials Research and Technology
This study investigated the low-cycle fatigue (LCF) behavior of Twinning induced plasticity (TWIP) steel based on the twin bridge shear specimen and cyclic shear loading condition.
Chen Jiaqi, Yang Yiming, Ren Qizhen, Qiu Yuliang, Yue Zhenming, Zhou Yiqi, Chu Xingrong   +6 more
doaj   +1 more source

Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC

Advanced Engineering Materials, EarlyView.
ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko, Evelyn Wang, Michael A. Hickner   +2 more
wiley   +1 more source

Performance Review of Strain-Hardening Cementitious Composites in Structural Applications. [PDF]

Materials (Basel), 2023
Xue B, Xu B, Lu W, Zhang Y.
europepmc   +1 more source

Investigation of Thermo‐Chemical Processes in Commercial MgO‐C Refractory Bricks With and Without MgO‐C Recyclate at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm, Jana Hubálková, Christian Schimpf, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +6 more
wiley   +1 more source

Influence of Strain Hardening Rate of Material on Temperature and Strain Distributions during Wire Drawing. [PDF]

Materials (Basel), 2023
Hwang JK.
europepmc   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Effect of the Dislocation Substructure Parameters of Hadfield Steel on Its Strain Hardening. [PDF]

Materials (Basel), 2023
Russakova A, Zhilkashinova A, Alontseva D, Abilev M, Khozhanov A, Zhilkashinova A.   +5 more
europepmc   +1 more source