Results 141 to 150 of about 512,239 (311)

Printability Metrics and Strain Rate Sensitivity of Multirole PVDF in Extrusion-Based Additive Manufacturing. [PDF]

Polymers (Basel)
Vidakis N, Nasikas NK, Michailidis N, Spyridaki M, Mountakis N, Argyros A, Papadakis VM, Moutsopoulou A, Petousis M.   +8 more
europepmc   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Extrudability, printability, and strain rate sensitivity metrics of lightweight thermoplastic polyimide (PI) in material extrusion (MEX) additive manufacturing. [PDF]

RSC Adv
Vidakis N, Michailidis N, Mountakis N, Spyridaki M, Argyros A, Efstratiadis VS, Stratakis E, Petousis M.   +7 more
europepmc   +1 more source

A New Explanation for the Effect of Dynamic Strain Aging on Negative Strain Rate Sensitivity in Fe-30Mn-9Al-1C Steel. [PDF]

Materials (Basel), 2019
Xing J, Hou L, Du H, Liu B, Wei Y.
europepmc   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Composition-Dependent Creep Resistance and Strain Rate Sensitivity of BCC Mg-Sc Alloy Studied via Nano-Indentation on Diffusion Couple. [PDF]

Materials (Basel)
Liu C, Xu G, Chen F.
europepmc   +1 more source

Toward Knowledge‐Based Workflows: A Semantic Approach to Atomistic Simulations for Mechanical and Thermodynamic Properties

Advanced Engineering Materials, EarlyView.
Knowledge‐based atomistic workflows are presented for mechanical and thermodynamic properties. By coupling modular simulations with ontology‐aligned metadata and provenance, Fe case studies on elastic behavior, defects, thermal properties, and Hall–Petch strengthening reveal how FAIR, queryable, and reusable simulation data can be generated. Mechanical
Abril Azócar Guzmán, Hoang‐Thien Luu, Sarath Menon, Tilmann Hickel, Nina Merkert, Stefan Sandfeld   +5 more
wiley   +1 more source

Strain Rate Sensitivity of Low Carbon Threaded Steel Rods of Grade 4.6. [PDF]

Materials (Basel)
Trajkovski J, Kunc R.
europepmc   +1 more source

Strain Rate Sensitivity of Tensile Properties in Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy: Experiments and Constitutive Modeling. [PDF]

Materials (Basel), 2018
Zhang J, Wang Y, Zhang B, Huang H, Chen J, Wang P.   +5 more
europepmc   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source