Results 211 to 220 of about 13,446,736 (354)

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Impact of anti-fracture medications on bone material and strength properties: a systematic review and meta-analysis. [PDF]

Front Endocrinol (Lausanne)
Sharma S, Shankar V, Rajender S, Mithal A, Rao SD, Chattopadhyay N.   +5 more
europepmc   +1 more source

Strength Properties of Structural Glulam Manufactured from Pine (Pinus sylvestris L.) Side Boards. [PDF]

Materials (Basel), 2021
Mirski R, Dziurka D, Kuliński M, Trociński A, Kawalerczyk J, Antonowicz R.   +5 more
europepmc   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Synergistic Effects of Polypropylene Fibers and Silica Fume on Structural Lightweight Concrete: Analysis of Workability, Thermal Conductivity, and Strength Properties. [PDF]

Materials (Basel)
Akbulut ZF, Kuzielová E, Tawfik TA, Smarzewski P, Guler S.   +4 more
europepmc   +1 more source

The Effect of Adding Modified Chitosan on the Strength Properties of Bacterial Cellulose for Clinical Applications. [PDF]

Polymers (Basel), 2021
Lipovka A, Kharchenko A, Dubovoy A, Filipenko M, Stupak V, Mayorov A, Fomenko V, Geydt P, Parshin D.   +8 more
europepmc   +1 more source

Effect of GGBFS on setting, workability and early strength properties of fly ash geopolymer concrete cured in ambient condition

, 2014
P. Nath, P. Sarker
semanticscholar   +1 more source

Evaluating rolling shear strength properties of cross-laminated timber by short-span bending tests and modified planar shear tests

Journal of Wood Science, 2017
Minghao Li
semanticscholar   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source