Results 161 to 170 of about 7,010 (230)

Hierarchical Interfacial Engineering of Boehmite‐Coated Separators via Silane Functionalization and Electron‐Beam Irradiation

Small, EarlyView.
A hierarchically reinforced ceramic–coated separator is developed by integrating APTES‐functionalized boehmite nanoparticles with EB‐induced radical formation and subsequent coupling. This synergistic interface engineering enables significantly improved mechanical integrity and interfacial stability.
Md Amir Sohel, Sungwoo Kim, Seunguk Cheon, Sung Oh Cho   +3 more
wiley   +1 more source

Ultrafast Laser‐Driven Crystallization of LTA Zeolite

Small Methods, EarlyView.
The ultrafast laser synthesis technique, using femtosecond laser pulses, enhances zeolite synthesis by providing high‐precision control over energy delivery and reaction kinetics. This technique accelerates the synthesis of high‐quality zeolite crystals with enhanced functionality.
Meryem Merve Doğan, Mehdi Hagverdiyev, Sezin Galioglu   +2 more
wiley   +1 more source

A Comparative Study of Directed Energy Deposition‐Arc and Casting: Enhancing Mechanical and Thermal Properties of Hot‐Work Tool Steels

steel research international, EarlyView.
The study investigates the influence of DED‐Arc/M versus casting on the microstructure and material properties of X40CrMoV5‐1 (AISI H13) hot‐work tool steel. DED‐Arc/M yields finer microstructures, superior mechanical strength, and ductility, but slightly reduced thermal conductivity.
Ulf Ziesing, Aaron Berger, Hendric Schaefer, Sebastian Weber, Jonathan Lentz   +4 more
wiley   +1 more source

Tailoring Laser Powder Bed Fusion and Post‐Processing Parameters for JIS SKD61 Tool Steels: Surface Roughness, Microstructure, and Mechanical Properties

steel research international, EarlyView.
Laser powder bed fusion of JIS SKD61 tool steel is systematically optimized using a Taguchi design and ANOVA. Hatch spacing and layer thickness are identified as dominant parameters controlling surface roughness and tensile strength. Subsequent tempering at 600°C improves microstructural stability and mechanical performance, enabling high‐density SKD61
Masrurotin Masrurotin, Andi Ard Maidhah, Maziar Ramezani, Wojciech Macek, Cho‐Pei Jiang   +4 more
wiley   +1 more source

Near‐Atomic Investigation on the Elemental Redistribution During Coprecipitation of Nano‐Sized Kappa‐Type and B2 Precipitates in an Al‐Alloyed Lightweight Steel

steel research international, EarlyView.
Elemental redistribution during coprecipitation of kappa (κ)‐type and B2 precipitates in an Al‐alloyed lightweight steel is revealed by atom probe tomography (APT) and density functional theory (DFT). Fe and Ni redistribution promotes the evolution of B2 phase from NiAl‐type toward FeAl‐type and improves the stability of κ and B2 phases during ...
Bowen Zou, Yixu Wang, Xiao Shen, Philipp Krooß, Thomas Niendorf, Richard Dronskowski, Wenwen Song   +6 more
wiley   +1 more source

Insights Into Paint‐Bake Toughening of Resistance Spot Welds of a 2.0 GPa Warm‐Stamped Medium‐Mn Steel

steel research international, EarlyView.
Paint baking of resistance spot welded joints of 2.0 GPa warm‐stamped medium‐Mn steel activates low‐temperature tempering, forming fine cementite in the fusion zone and enhancing toughness. Crack propagation resistance increases, shifting the failure mode from partial interfacial to complete pullout, with peak load and energy absorption rising ...
Sunusi Marwana Manladan, Savyasachi Nellikode, YeoJin Jang, Sumin Lee, Dileep Chandran Ramachandran, Sung‐bo Heo, Jinyoung Lee, Young‐Kook Lee, Yeong‐Do Park   +8 more
wiley   +1 more source

Crash Behavior of DP800–DP1000 Advanced High‐Strength Steel’s Dissimilar Resistance Spot Welded Joints Under Quasi‐static and High Strain Rates

steel research international, EarlyView.
The high‐strain‐rate behavior of resistance spot‐welded DP800–DP1000 joints is investigated. Results show that microstructural gradients across BM–HAZ–FZ govern hardness, strain rate sensitivity, and failure modes. While strength increases with strain rate, energy absorption is controlled by ductility, with DP800–DP800 joints showing superior ...
Pankaj Shrivastava, Velaphi Msomi
wiley   +1 more source

Tailored Hardening and Isothermal Bainitizing of Additively Manufactured Nitrogen‐Enhanced Martensitic Chromium Steel

steel research international, EarlyView.
Tailored heat treatments transform additively manufactured high‐nitrogen martensitic Cr steel from austenitic as‐built condition to high‐hardness states. Isothermal bainitizing at 250°C generates an ultrafine nanostructure and achieves higher hardness than conventional hardening and tempering, highlighting a promising postprocessing route for laser ...
Philip König, Sebastian Weber, Jonathan Lentz   +2 more
wiley   +1 more source

Woven Eutectic Lamellar Structures Lead to Ultrahigh Strength and Energy Absorption Capacity in Additively Manufactured Lattice Structures

Small Structures, Volume 6, Issue 5, May 2025.
Herein, AlCoCrFeNi2.1 is selected to produce lattice structures by selective laser melting. The as‐printed lattice structures consist of numerous colonies of nanosized eutectic lamellar structures which are bent and interwind with each other to form a woven microstructure. The unique microstructure leads to unprecedented effective metal strength, yield
Zhiyong Ji, Xingyu Pan, Longlong Wang, Xintian Wang, Xu Chen, Hanwei Fu, Chunlei Qiu   +6 more
wiley   +1 more source

Evaluations of the effectiveness of the near‐surface mounted steel materials in strengthening short RC wall‐like columns with openings

Structural Concrete, EarlyView.
Abstract In practice, reinforced concrete (RC) wall‐like columns often have openings to facilitate building services, which creates stress concentrations around the opening, resulting in the weakening of their load‐carrying capacity. This study proposes innovative strengthening methods using near‐surface mounted (NSM) incorporating steel materials to ...
Ahmed Hamoda, Mizan Ahmed, Mohamed Ghalla, Ahmad G. Saad, Aref A. Abadel   +4 more
wiley   +1 more source