Results 141 to 150 of about 289,087 (265)

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Modular Critical Element Recycling Platform Using a Nanoporous Additively Manufactured Gyroid

Advanced Engineering Materials, EarlyView.
A modular recycling platform integrates 3D‐printed nanoporous gyroid structures to enable efficient critical element recovery. This system utilizes a hierarchical architecture, combining macroscopic channels with polymerization‐induced nanoscale porosity. By systematically tuning structural wall thickness and resin formulation, the platform achieves an
Xiangyu Gao, Keldy Mason, Mert Gülçür, Rachel Paddock‐Lamb, Prince Alvin Fofanah, Zachariah A. Page, Michael Cullinan   +6 more
wiley   +1 more source

Stress-strain-time Behavior of Powders.

Journal of the Society of Powder Technology, Japan, 1994
openaire   +2 more sources

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Molecular Dynamics Studies of Shape Memory Polymers: From Bead–Spring Models to Atomistic Simulations

Advanced Engineering Materials, EarlyView.
Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Modeling Dislocation Cutting of γ′ Precipitates in Ni‐Base Superalloys: Linking Atomistic and Dislocation Dynamics Simulations

Advanced Engineering Materials, EarlyView.
Dislocation cutting of γ′ precipitates in Ni‐based superalloys is investigated by linking atomistic simulations with discrete dislocation dynamics. The critical cutting stress is shown to be governed by the antiphase boundary energy, while line tension effects promote edge‐preferred cutting.
Frédéric Houllé, Siwen Gao, Marc Fivel, Anxin Ma, Daria Smirnova, Sriram Anand, Arun Prakash, Julien Guénolé, Alexander Hartmaier, Erik Bitzek   +9 more
wiley   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source