Results 81 to 90 of about 8,893 (213)

Stress corrosion in titanium alloys and other metallic materials [PDF]

Multiple physical and chemical techniques including mass spectroscopy, atomic absorption spectroscopy, gas chromatography, electron microscopy, optical microscopy, electronic spectroscopy for chemical analysis (ESCA), infrared spectroscopy, nuclear ...
Basu, P. K., Brotzen, F. R., Harkins, C. G., Hightower, J. W., Leith, I. R., Mclellan, R. B., Parris, D. P., Roberts, J. M., Rudee, M. L., Salama, K.   +9 more
core   +1 more source

Titanium alloy stress corrosion cracking in presence of dinitrogen tetroxide [PDF]

, 1972
Study resulting in a satisfactory stress corrosion cracking test with extremely consistent results produced six new analytical methods. Methods detect and determine differences in the minor constituent composition of different types of dinitrogen ...
Clarke, J. F. G., Jr., Conner, A. Z., Gailey, J. A., Orr, A. A.   +3 more
core   +1 more source

Enhancement resistance to microbiologically influenced stress corrosion of Cu-bearing steel against Bacillus cereus

npj Materials Degradation
Microorganisms are notoriously known to cause local corrosion and stress corrosion cracking (SCC), which seriously endangers the materials service safety.
Bo Liu, Fangyuan Lu, Shidong Zhu, Cuiwei Du, Xiaogang Li   +4 more
doaj   +1 more source

Clarifying stress corrosion cracking behavior of biomedical Mg-Gd-Zn-Zr alloy

Journal of Magnesium and Alloys
Implants are inevitably subjected to stress corrosion, bringing serious challenges to the controlled degradation of biomedical Mg alloys. It is worth studying the stress corrosion cracking (SCC) behavior of Mg alloy and exploring Mg alloy with good SCC ...
Qiangsheng Dong, Jiahao Jiang, Jinghuai Zhang, Zhi Hu, Xiaobo Zhang   +4 more
doaj   +1 more source

Stress corrosion cracking evaluation of martensitic precipitation hardening stainless steels [PDF]

The resistance of the martensitic precipitation hardening stainless steels PH13-8Mo, 15-5PH, and 17-4PH to stress corrosion cracking was investigated. Round tensile and c-ring type specimens taken from several heats of the three alloys were stressed up ...
Humphries, T. S., Nelson, E. E.
core   +1 more source

Analysis, Assessment, and Mitigation of Stress Corrosion Cracking in Austenitic Stainless Steels in the Oil and Gas Sector: A Review

Surfaces
This comprehensive review examines the phenomena of stress corrosion cracking (SCC) and chloride-induced stress corrosion cracking (Cl-SCC) in materials commonly used in the oil and gas industry, with a focus on austenitic stainless steels.
Mohammadtaghi Vakili, Petr Koutník, Jan Kohout, Zahra Gholami   +3 more
doaj   +1 more source

Study of the general mechanism of stress corrosion of aluminum alloys and development of techniques for its detection Quarterly report, 1 May - 31 Aug. 1968 [PDF]

Mechanism of stress corrosion cracking in aluminum alloys and techniques for detection of surface ...
Bell, R. O., Brummer, S. B., Cocks, F. H., Cordellos, A.   +3 more
core   +1 more source

Surface aspects of pitting and stress corrosion cracking [PDF]

The pitting and stress corrosion cracking of a stable austenitic stainless steel in aqueous chloride environments were investigated using a secondary ion mass spectrometer as the primary experimental technique.
Hehemann, R. F., Truhan, J. S., Jr.
core   +1 more source

The Determination Of K ISCC Of Mild Steel In Hot Caustic By Using Small Circumferential Notched Tensile (CNT) Fracture Toughness Specimens [PDF]

, 2004
A new technique for rapid and cost-effective determination of stress intensity factor (K I) and fracture toughness (K IC) using small circumferential notch tensile (CNT) specimens is presented and used to determine the crack growth rate of an ex-service ...
Ibrahim, R. N., Rihan, R., Singh Raman, R. K.   +2 more
core  

Fundamental investigation of stress corrosion cracking [PDF]

Two principle areas studied were stress corrosion crack growth rates of a titanium alloy in liquid environments containing halide ions and pitting corrosion of titanium in bromide solutions. Two initial assumptions were made, that the rate of propagation
Beck, T. R., Blackburn, M. J., Smyrl, W. H.   +2 more
core   +1 more source