Results 141 to 150 of about 249,856 (305)

Strong ground motion characteristics of 2016 Central Italy earthquakes and implications for ground motion modeling [PDF]

, 2019
The 2016 Central Italy earthquake sequence produced three mainshocks: (1) M6.1 24 August, (2) M5.9 26 October, and (3) M6.5 30 October. Each mainshock was followed by many aftershocks, some of which with M > 5.0. All earthquake events occurred on southeast-northwest trending normal faults.
Zimmaro P., Stewart J. P., Scasserra G., Kishida T., Tropeano G.   +4 more
openaire   +2 more sources

Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma

Advanced Engineering Materials, EarlyView.
The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie, David Kramer, Thomas Scheithauer, Hans Jürgen Maier, Thomas Hassel   +4 more
wiley   +1 more source

РАЗРАБОТКА БАЗЫ ДАННЫХ СИЛЬНЫХ ДВИЖЕНИЙ

Геология и геофизика Юга России, 2015
В работе рассмотрены структура и принципы построения базы данных сильных движений, созданной на основе инструментальных записей землетрясений системы KNET с мая 1996 г.
В.Б. Заалишвили, К.С. Харебов, А.К. Харебов   +2 more
doaj  

Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann, Berend Denkena, Hilke Petersen, Florian Schaper   +3 more
wiley   +1 more source

СОЗДАНИЕ БАЗ ДАННЫХ СИЛЬНЫХ ДВИЖЕНИЙ НА ОСНОВЕ СОВРЕМЕННЫХ ВОЗЗРЕНИЙ

Геология и геофизика Юга России, 2014
В работе рассмотрена структура и принципы построения базы данных сильных движений созданной на основе инструментальных записей землетрясений системы KNET с 1996 г по 2012 г.
В. Б. Заалишвили, К. С. Харебов, А. К. Харебов   +2 more
doaj  

Localization of strong ground motions

Proceedings of the Japan Academy, Series B, 2001
Qinghua HUANG, Masashi KAMOGAWA, Torn OUCHI   +2 more
openaire   +2 more sources

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

Advanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Investigation of Oxygen‐Free Wetting Behavior of Aluminum on Copper via Molecular Dynamics Simulations and Experiments

Advanced Engineering Materials, EarlyView.
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu, Timon Steinhoff, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Christian Klose, Ludger Overmeyer, Hans‐Jürgen Maier, Nina Merkert   +8 more
wiley   +1 more source

Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties

Advanced Engineering Materials, EarlyView.
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat, Guido Barale, John Stavridis, Ehsan Norouzi, Jin‐Yoo Suh, Dong‐Ik Kim, Luca Iuliano, Abdollah Saboori   +7 more
wiley   +1 more source