Results 141 to 150 of about 3,319,169 (244)

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Ferromagnetism in the two-dimensional Hubbard model with long-range hopping

Open Physics, 2013
Farkašovský Pavol, Čenčariková Hana
doaj   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel

Advanced Engineering Materials, EarlyView.
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe, Louis Becker, Gaurav Kanu, Thomas F. Headen, Dirk Honecker, Gabi Schierning, Santiago Benito, Sebastian Weber, Klara Lünser, Sabrina Disch   +9 more
wiley   +1 more source

Lifshitz Transition in Correlated Topological Semimetals

Advanced Science
Topological quasiparticles that arise when the chemical potential is near a band crossing are pivotal to next‐generation quantum devices. Nonetheless, correlated topological materials frequently host Dirac nodes away from the Fermi level, and the cause ...
Byungkyun Kang, Myoung‐Hwan Kim, Chul Hong Park, Anderson Janotti, Eunja Kim   +4 more
doaj   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

Advanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo, João Marcos da Silva Nunes, Marcelly Cristiny Nunes de Carvalho, Alex Rojas, Cristie Luis Kugelmeier, Cristhian Ricardo Loayza Loayza, João Carlos Ferreira, Maria Veronica Goncalves Rodrigues, Rute Sayuri Kano, Isaac Araújo Furtado, Jacyara Dalylla da Silva Nunes, Jhonatan Peres de Sousa, Marcos Natan da Silva Lima, Eden Santos Silva, Gedeon Silva Reis, Samuel Filgueiras Rodrigues   +15 more
wiley   +1 more source

Influence of Particle Shape and Size in Copper‐Based Low‐Temperature Metallization Paste for Solar Cells

Advanced Engineering Materials, EarlyView.
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi, M. N. Wengenmeyr, J. Bartsch, B. E. Rapp   +3 more
wiley   +1 more source

Gyroid Structured Globugraphite Carbon Foam With Hierarchical and Tailored Pore Size

Advanced Engineering Materials, EarlyView.
Secondary sacrificial templates were designed and printed to create a defined network within a porous carbon. Lattices thermally degrades during the sintering process. Lattices are imprinted into the ceramic template and transferred to the morphology of Globugraphite.
Christiane Roller, Justin Neumann, David Ploch, Lennard M. Flohr, Julian Karsten, Fabian A. Riebesehl, Bodo Fiedler   +6 more
wiley   +1 more source

Microstructural, Mechanical, and Textural Evolution of Dissimilar Combination of Laser‐Welded Maraging Steel and 4340 Steel

Advanced Engineering Materials, EarlyView.
The present work reports the microstructural, mechanical, and texture evolution of a dissimilar combination laser‐welded maraging steel with 4340 steel. This is important for aerospace applications. The demand for dissimilar welding is growing rapidly with the requirement of efficient and durable joints.
Bharat Behl, Yu Dong, Alokesh Pramanik, Tapas Kumar Bandyopadhyay   +3 more
wiley   +1 more source