Results 161 to 170 of about 1,147,751 (192)
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones
Advanced Engineering Materials, EarlyView.A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell +3 more
wiley +1 more source
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source