Results 141 to 150 of about 479 (195)

Controlled Mechanical Property Gradients Within a Digital Light Processing Printed Hydrogel-Composite Osteochondral Scaffold. [PDF]

Ann Biomed Eng
Eckstein KN, Hergert JE, Uzcategui AC, Schoonraad SA, Bryant SJ, McLeod RR, Ferguson VL.   +6 more
europepmc   +1 more source

Study on Strut and Node Behavior in Strut-and-Tie Modeling

, 2019
openaire   +2 more sources

Visualising joint force-velocity properties in musculoskeletal models

Richards CT, Murtola T.
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Strut-and-tie model design provisions

PCI Journal, 2011
The overall objective of the research project summarized in this paper was to develop simple and safe design guidelines for deep beams. To accomplish the research objective and related tasks, a database of 868 deep-beam tests was assembled from previous research.
Robin G. Tuchscherer, David B. Birrcher, Oguzhan Bayrak   +2 more
openaire   +1 more source

Corbel strut and tie modeling – Experimental verification

Structures, 2020
Abstract ACI 318-14 analyzes reinforced concrete corbel by shear friction (SF) and/or strut-and-tie modeling (STM). This work presents the results of experimental tests conducted on three reinforced concrete corbels that had a height of 390 mm and a width of 115 mm. The corbels had different shear span to effective depth ratios (a/d), which were 0.5,
Khattab Saleem Abdul-Razzaq, Asala Asaad Dawood   +1 more
openaire   +1 more source

Strut and Tie Models

SP-198: Structural Concrete - Behavior to Implementation, 2001
The evolution of strut and tie models is reviewed and their characteristics are discussed. From their evolution it is seen that more design effort should be expended on developing a reasonable truss than on refined calculations of nodal stresses and permissible concrete stresses. Strut and tie models are design tools.
openaire   +1 more source

Direct Strut-and-Tie Model for Prestressed Deep Beams

Journal of Structural Engineering, 2001
The strut-and-tie method is a promising analytical tool for the design of disturbed regions where the conventional plane bending theory does not hold. These include pile caps, corbels, frame joints, deep beams, and so forth. This paper focuses on the application of a strut-and-tie model to prestressed deep beams.
Tong, K, Tan, KH, Tang, CY
openaire   +2 more sources

The Preliminary Calculation Process of Strut-and-Tie Model

Applied Mechanics and Materials, 2013
By briefly introducing the main steps of using strut-and-tie (STM) , this paper showing the preliminary calculation process. In this paper, defining D-region is the very first step in design.Then paper gives the method to calculate the reinforcement needed to meet required tie capacities.
Hao Jun Gong, Min Su
openaire   +1 more source

Stress Fields for Nodes of Strut‐and‐Tie Models

Journal of Structural Engineering, 1990
Truss models have been developed and applied to the ultimate strength design and detailing of two‐dimensional reinforced concrete members loaded in their plane. Such a truss is composed of struts and ties which represent one‐dimensional stress fields. The nodes, however, form two‐dimensional stress fields whose bearing capacity also needs to be checked.
Michael Schlaich, Georg Anagnostou
openaire   +1 more source

Modelling Structural Concrete with Strut-and-Tie Model Combined with 2D Finite Elements - A Model Factor for the Assessment of Strut-and-Tie Models

2017
Despite being a widely used structural material, the deep knowledge on behaviour of structural concrete represents a continuous challenge to the technical community. The definition of local and global interactions between materials, the accurate definition of its geometry, supports and loads are basic requirements to establish adequate models to ...
Miguel Pedrosa Ferreira, João F. Almeida, Miguel Sério Lourenço   +2 more
openaire   +1 more source