Results 171 to 180 of about 1,733 (215)

The Preliminary Calculation Process of Strut-and-Tie Model

Applied Mechanics and Materials, 2013
By briefly introducing the main steps of using strut-and-tie (STM) , this paper showing the preliminary calculation process. In this paper, defining D-region is the very first step in design.Then paper gives the method to calculate the reinforcement needed to meet required tie capacities.
Hao Jun Gong, Min Su
openaire   +1 more source

Modelling Structural Concrete with Strut-and-Tie Model Combined with 2D Finite Elements - A Model Factor for the Assessment of Strut-and-Tie Models

2017
Despite being a widely used structural material, the deep knowledge on behaviour of structural concrete represents a continuous challenge to the technical community. The definition of local and global interactions between materials, the accurate definition of its geometry, supports and loads are basic requirements to establish adequate models to ...
Miguel Pedrosa Ferreira, João F. Almeida, Miguel Sério Lourenço   +2 more
openaire   +1 more source

Practical Design with Strut-and-Tie Models

Structures 2001, 2001
Strut-and-tie models are an especially valuable tool for designing discontinuity regions (D-regions) of structures with irregular geometry where the flow of forces is not well known, like at points where high forces are applied to a beam, for shear walls with openings or for connections of members. The latter is especially important for highly stressed
openaire   +1 more source

An Overview of Strut-and-Tie Model and its Common Challenges

International Journal of Engineering Research in Africa, 2012
B-Regions are parts of the structure in which Bernoulli's principle of straight-line strain is used. D-Regions are parts of the structure with a complicated variation in strain. In essence, D-Regions contain the parts of structure which are near to the concentrated forces or steep changes in geometry which are so-called geometrical discontinuities or ...
Mohammad Panjehpour, Abang Abdullah Abang Ali, Anwar Mohammed Parvez, Farah Nora Aznieta, Yen Lei Voo   +4 more
openaire   +1 more source

Optimal strut-and-tie models in reinforced concrete structures

1999
zbMATH Open Web Interface contents unavailable due to conflicting licenses.
BIONDINI, FABIO, BONTEMPI, FRANCO, MALERBA, PIER GIORGIO   +2 more
openaire   +3 more sources

Design of Pile Caps With Strut-and-Tie Models

"SP-209: ACI Fifth Int Conf Innovations in Design with Emphasis on Seismic, Wind and Environmental Loading, Quality Con", 2002
The present ACI Building Code (ACI 318-99) procedure for shear design of pile caps is the same approach used for 2-way slabs. The procedure involves determining a section thickness such that the concrete shear stress is greater than the applied shear stress on the critical section.
openaire   +1 more source

Strut-And-Tie Models

2022
Franco Angotti, Matteo Guiglia, Piero Marro, Maurizio Orlando   +3 more
openaire   +1 more source

APPLICATION OF STRUT-AND-TIE MODELS IN THE ANALYSIS OF RC WALLS

Zbornik radova
This paper presents the application of Strut-and-Tie Models (STM) for the analysis of reinforced concrete (RC) walls. STM, as a system of compressed and tensioned struts and nodes where the struts intersect, enables the tracking of force flow and principal stresses in structural elements.
Boris Folić, Radomir Folić, Miloš Čokić   +2 more
openaire   +1 more source

Shear strength evaluation of RC D-Regions based on Single-Panel Strut-and-Tie model

Engineering Structures, 2022
Hui Chen, Yun Zhou, Ye Li
exaly  

Developing a Strut-and-Tie Model

2017
Salah El-Din E. El-Metwally, Wai-Fah Chen   +1 more
openaire   +1 more source