Results 31 to 40 of about 12,659 (225)
Secondary ledeburite formation during various welding techniques [PDF]
Journal of Mining and Metallurgy. Section B: Metallurgy, 2015 The occurrence and formation sequence of secondary ledeburite in the heat affected zone of chromium ledeburitic tool steel W.Nr. 1.2379 (OCR12 VM) after welding with SAW, TIG, microplasma and laser welding techniques is presented in this paper ...
Tonkovič M.P. +3 more
doaj +1 more source
Friction stir welding of thin DH36 steel plate [PDF]
, 2013 A series of 4, 6 and 8 mm DH36 steel welds were produced using optimum conditions for friction stir welding (FSW). Comparator welds in the same thickness from the same plates were produced using a single sided single pass process submerged arc welds (SAW)
Cater, Stephen R. +3 more
core +1 more source
Welding quality and sustainability of alternative LPG valve boss welding processes [PDF]
Songklanakarin Journal of Science and Technology (SJST), 2019 This work aimed to evaluate the welding quality and the sustainability of an automatic metal active gas with mixing gases (MAG-M) process for welding the valve boss on liquefied petroleum gas (LPG) upper cylinder half, in comparison to the presently ...
Thiensak Chucheep +4 more
doaj +1 more source
Trends in Development of Weld Overlaying During The 21ST Century
Acta Technologica Agriculturae, 2014 The present article discusses the trends in the development of welding and weld overlaying on the threshold of the new millennium and during it. It presents the trends in the production of welding materials for welding and weld overlaying in industrially
Nikolov Mitko
doaj +1 more source
Optimalisasi Komposisi Kandungan MN Pada Filler untuk Mendapatkan Ketangguhan dan Kekerasan
Jurnal Teknik Industri, 2012 Submerged Arc Welding (SAW) is a welding process used for fabrication of pipes, for example spiral welded pipes. The technique can be operated automatically and has a high reliability in many various welding applications.
Nur Subeki
doaj +1 more source
Hot Forging of a Cladded Component by Automated GMAW Process [PDF]
, 2010 Weld cladding is employed to improve the service life of engineering components by increasing corrosion and wear resistance and reducing the cost. The acceptable multi-bead cladding layer depends on single bead geometry.
BIGOT, Régis +2 more
core +4 more sources
A comprehensive study on the microstructure and mechanical properties of arc girth welded joints of spiral welded high strength API X70 steel pipe [PDF]
, 2020 In the paper, the effect of welding technology on the microstructure and mechanical properties of girth welded joints was presented. Metallographic examinations based on light microscopy and SEM were conducted on girth welded joints of API X70 steel pipe.
De Waele, Wim +6 more
core +1 more source
Performance of historical ferrocement specimens subjected to corrosive environments
Structural Concrete, Volume 26, Issue 5, Page 5785-5806, October 2025.Abstract Ferrocement is a type of thin wall‐reinforced concrete composed of hydraulic cement mortar reinforced with several layers of steel wire mesh. The material is used as a low‐cost construction and retrofit solution and allows the creation of very thin elements.
Erica Lenticchia +3 more
wiley +1 more source
Journal of Materials Exploration and FindingsThis review studying the correlation between microstructural transformations and mechanical properties in reconditioned low-allow steel material, focusing on the impact of Submerged Arc Welding (SAW) parameters, especially current, on microstructure ...
Iman Nugraha Asmara, Winarto
doaj +1 more source
Effect of cold wire position on the welding process in twin-arc integrated cold wire hybrid welding
工程科学学报, 2021 With rapid social and economic development, high-efficiency welding technology has become an important development direction in the field of welding.
Ting XIANG +5 more
doaj +1 more source