Results 61 to 70 of about 256 (172)
Applied Sciences, 2019 The article presents the modeling of temporary temperature and phase share calculations during SAW (submerged arc welding) overlaying of steel elements. The input heat of a melted electrode and the heat of direct electric arc impact have been taken into ...
Jerzy Winczek +3 more
doaj +1 more source
Processing and characterization of submerged arc welding (SAW) flux [PDF]
, 2011 Submerged arc welding (SAW) is a process that melts and joins metals by heating them with an arc established between a consumable wire electrode and the metals, with the arc being shielded by a molten slag and granular flux.SAW flux is an important welding consumable material which may tend to welding defect such as inclusions if not properly selected.
openaire +1 more source
Journal of Mechanical Engineering Research, 2013 Performance of a welding flux is decided by the physical and chemical properties of its constituents. The flux selected should show a good welding behavior and the required weld bead geometry. The mechanical properties of a joint are not only decided by its composition but these also depends on bead geometry, dimensions and physico-chemical properties ...
openaire +2 more sources
Scripta Metallurgica et Materialia, 1995 The origin of acicular ferrite in the weld metal of submerged arc weldments on high strength steels is very complex and depends upon the chemical composition for the steel base plate and filler wire, the composition of the flux used during welding and the cooling rate of the weld metal during the transformation of the undercooled metastable austenite ...
Fox, A.G., Brothers, D.G.
openaire +2 more sources
Microstructure Characterization of SAW and TIG Welded 25Cr2Ni2MoV Rotor Steel Metal
Metals, 2020 Low pressure turbine rotors are manufactured by welding thick sections of 25Cr2Ni2MoV rotor steel using tungsten inert gas (TIG) backing weld, and submerged arc welding (SAW) filling weld.
Chaoyu Han +5 more
doaj +1 more source
Recycling of submerged arc welding slag for sustainability
Production and Manufacturing Research: An Open Access Journal, 2020 The objective of this paper is to investigate the utilization of Submerged Arc Welding (SAW) slag as a fresh flux for sustainability. Certain alloying elements were added to the crushed slag to adjust the resultant composition of the weld metal as per ...
Deepanjali Nimker, Reeta Wattal
doaj +1 more source
Revista de Gestão e SecretariadoConcern about the environment and the scarcity of natural resources has led to the search for more sustainable alternatives that minimize the environmental impact of all segments of society. Solid waste recycling has been presented as a good alternative to reduce the impacts generated by the disorderly use of raw materials and the reduction of disposal
Millena Varela de Moura +5 more
openaire +2 more sources
, 2019 This work describes an investigation on the effect of filler metals diameter to weld joint, and low alloy carbon steel A516 Grade 70 is the base metal. Commercially SA516 Grade70 is frequently used for the manufacturing of pressure vessels, boilers and storage tank, etc.
A. Nait Salah, M. Kaddami
openaire +1 more source
The modeling of heat affected zone (HAZ) in submerged arc welding (SAW) surfacing steel element
Metalurgija, 2016 In the work the bimodal heat source model in the description of the temperature field is presented. The electric arc was treated physically as one heat source, whose heat was divided: part of the heat is transferred by the direct impact of the electric arc, but another part of the heat is transferred to the weld by the melted material of the electrode.
Winczek, J., Gawrońska, E.
openaire +2 more sources
Medžiagotyra, 2018 EComposite hardfacings produced by Plasma Transferred Arc Welding (PTAW) and Submerged Arc Welding (SAW) possess a good combination of hardness, wear resistance and fracture toughness, thus providing high wear resistance.
Taavi SIMSON +5 more
doaj +1 more source