Results 31 to 40 of about 207 (134)

Strategies for Mitigating Anti‐Nutritional Factors in Legumes: A Review of Traditional and Innovative Processing Techniques for Enhanced Bioavailability

Legume Science, Volume 8, Issue 4, December 2026.
ABSTRACT Legumes (family Fabaceae) are vital, nutrient‐dense global resources rich in proteins, complex carbohydrates and micronutrients. Although offering agronomic benefits like nitrogen fixation, their dietary utilization is often constrained by anti‐nutritional factors (ANFs) such as phytates, tannins, lectins and oligosaccharides, which reduce ...
Diana Kavaya, Muhammad Siddiq, Leonard M. P. Rweyemamu, Lilian Daniel Kaale   +3 more
wiley   +1 more source

Effect of processing environment during friction stir processing of AZ31/(ZrO2+CuO)p surface composite on the mechanical and tribological performance

Journal of Materials Research and Technology
In this work, the AZ31 Mg alloy was subjected to friction stir processing (FSP) by adding CuO and ZrO2 particles. The main aim of this study was to increase the tribological and mechanical behavior of AZ 31/(CuO + ZrO2)p surface composite in air and ...
Liang Huang, Moslem Paidar, Azlan Mohd Zain, Mohamad Reda A. Refaai, Sherzod Abdullaev, Michaela Šlapáková   +5 more
doaj   +1 more source

Dissecting the dissection laboratory: Elements for designing a human anatomy laboratory

Anatomical Sciences Education, Volume 19, Issue 11, Page 1823-1860, November 2026.
Abstract The human anatomy dissection laboratory is a critical component of anatomical and medical education. Development, maintenance, and stocking of these laboratory spaces have unique demands, with all of the challenges in running a laboratory with Biosafety Laboratory Level 2 (BSL‐2) classification, housing a large volume of tissues saturated with
Rhiannon E. Robinson, Abbey Breckling, Danielle N. Edwards, Nicole Geske, Burhan Gharaibeh, Bobbie J. Leeper, Molly Ostwald, Mary Schilling, Bridgett Severt, Kelsey Stevens, J. P. Swigart, Jonathan J. Wisco, Melissa Zolnierz, Jeremy J. Grachan   +13 more
wiley   +1 more source

Tropical Plantains, Tubers, and Roots: Advancing Food Quality, Safety, and Processing Innovations for Global Nutritional Equity

Food Science &Nutrition, Volume 14, Issue 11, November 2026.
Plantains, tubers, and roots (PTRs) represent strategic nutritional and caloric pillars for over 500 million people across tropical regions. This review evaluates traditional bioprocessing against eco‐innovative thermomechanical and non‐thermal technologies (HPP, extrusion, encapsulation) to overcome severe post‐harvest losses and antinutritional risks.
Mundéné‐Timothée Junior Lawrence, Veeranna Hitlamani, Njintang Yanou Nicolas, Aashitosh A. Inamdar   +3 more
wiley   +1 more source

Oil‐In‐Water or Water‐In‐Oil Pickering Emulsion: Role of Lignocellulose‐Based Nanoparticle Wettability and Geometry

Small Science, Volume 6, Issue 11, November 2026.
Lignocellulose nanoparticles with tunable wettability and geometry can allow the tailored design of sustainable, surfactant‐free Pickering emulsions. Particle wettability dictates emulsion type, switching between oil‐in‐water and water‐in‐oil. Spherical lignin nanoparticles adsorb at the oil–water interface to create small droplets, while lignin ...
Nissa Nurfajrin Solihat, Muhammad Farooq, Juan José Valle‐Delgado, Elijah Mark Garcia, Kristoffer Meinander, Monika Österberg   +5 more
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, Volume 28, Issue 19, 7 October 2026.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Bioinspired Adaptive Surfaces for Intelligent Liquid Manipulation: Progressing From Passive and Active to Hybrid Strategies

Advanced Materials, Volume 38, Issue 56, 8 October 2026.
This review examines passive, active, and hybrid liquid manipulation strategies, highlighting hybrid approaches as an emerging route to reconcile energy efficiency with adaptive control. By actively reconstructing passive surfaces to store programmable interfacial energy, hybrid systems enable flexible yet low‐power liquid transport, with perspectives ...
Jiaqi Miao, Yiyuan Zhang, Liqiu Wang, Alan C. H. Tsang   +3 more
wiley   +1 more source

Laser Surface Treatment of Nickel‐Alumina Coating for Enhancement of Erosion and Corrosion Resistance of High Speed Steel Vanes

Applied Research, Volume 5, Issue 5, October 2026.
Laser surface treatment was carried out to enhance the performance of Ni‐Al2O3 coatings on HSS substrates. The results revealed improved microstructural features, corrosion resistance and significant reduction in slurry erosion wear with 18 W laser treatment. ABSTRACT The sliding wear between hydraulic vane tip and the inner surface of the cam ring can
Majunath Keshav, Achutarao Bharatish, Sivakumar Solaiachari, Srilatha Rao   +3 more
wiley   +1 more source

SUBMERGED FRICTION STIR PROCESSING OF EN AW 7075 ALUMINUM ALLOY

Nonconventional Technologies Review
Friction stir processing is a process for processing metallic materials that aims to locally modify the microstructure and mechanical properties. Submerged friction stir processing aims to limit the process temperature by using a liquid working medium ...
Lia Nicoleta Botila, Ion Aurel Perianu, Iuliana Duma, Gabriela Victoria Mnerie   +3 more
doaj  

CONSIDERATIONS REGARDING DEFECTS THAT MAY OCCUR DURING FSP/SFSP PROCESSING OF ALUMINUM ALLOYS

Nonconventional Technologies Review
The paper provides a comprehensive analysis of the defect phenomena associated with friction stir processing (FSP) and submerged friction stir processing (SFSP) of aluminium alloys.
Gabriela Victoria Mnerie, Lia Nicoleta Botila   +1 more
doaj