Results 31 to 40 of about 38,426 (298)
Wave Induced Pressures on Submerged Plates
Journal of the Waterways, Harbors and Coastal Engineering Division, 1975 In the analysis, the plate is imagined to be rigidly suspended at an arbitrary fixed depth and then replaced by a vortex sheet the strength of which varies both temporarily and spatially. The velocity potential of this sheet is adjusted such that, when combined with the potential of the oncoming waves, boundary conditions on the plate, the free surface,
Durgin, William W., Shiau, Jong C.
openaire +2 more sources
The impact of inlet flow conditions on the aerodynamic performance of a NACA submerged intake for ground vehicle applications [PDF]
, 2013 Results are presented following a series of experimental measurements on a submerged NACA type intake orientated between ±30 degrees yaw to the free stream in an atmospheric boundary layer wind tunnel at a unit Reynolds number of nominally 1 x 106.
Garry, Kevin P., Holt, Jennifer C.
core +1 more source
Surface wave scattering by an elastic plate submerged in water with uneven bottom
Mathematical Modelling and Analysis, 2020 Wave interaction with a vertical elastic plate in presence of undulating bottom topography is considered, assuming linear theory and utilizing simple perturbation analysis.
Souvik Kundu, Rupanwita Gayen
doaj +1 more source
Energy Reports, 2022 In this study, the power absorption of a submerged piezoelectric wave energy converter (PWEC) device floating over a rippled seabed is investigated under the linear water wave theory.
Vipin V., Kshma Trivedi, Santanu Koley
doaj +1 more source
Submerged jet impingement cooling using nanostructured plates
International Journal of Heat and Mass Transfer, 2013 Abstract In this paper, the results of a series of heat transfer experiments conducted on a compact electronics cooling device based on single and two phase jet impingement technique are reported. Deionized and degassed water is propelled into four microchannels.
Şeşen, Muhsincan +5 more
openaire +3 more sources
Defence Technology, 2019 Submerged arc welding (SAW), owing to its high deposition rate and high welding quality, is widely used in the fabrication of pressure vessel, marine vessel, pipelines and offshore structures.
Ankush Choudhary +2 more
doaj +1 more source
Scattering of Short-Wave Groups by Submerged Horizontal Plate [PDF]
, 1991 A fully submerged horizontal plate has been suggested as a breakwater. With a proper design in the length, thickness, and submerged depth of the plate, most of the incoming short waves can indeed be reflected.
Iskandarani, Mohamed, Liu, Philip L.-F
core +1 more source
Energies, 2020 As a kind of water jet technology with strong impinging force and simple structure, the submerged impinging water jet can produce strong scouring action on subaqueous sediments.
Hongliang Wang +4 more
doaj +1 more source
Study on the Radiation Forces on a Pontoon Type Floating Structure and Submerged Plate : Hydrodynamic Interaction Effect by Submerged Plate [PDF]
Journal of Korean navigation and port research, 2007 Hydroelastic deformation of pontoon type floating structure in waves is critical in structural design. Therefore, it is necessary to develop additional technology that make to dissipate the wave energy as the submerged horizontal plate. In this study, we investigate the characteristics of hydrodynamic interaction effect by the submerged plate affecting
openaire +1 more source
A novel inverter twin wires high effect submerged arc welding equipment for steel plate welding
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2015 Twin wires submerged arc welding technology is an efficient way for the high-speed welding of heavy workpiece of the low carbon steel. A novel inverter twin wires high effect submerged arc welding equipment is proposed by combination of the inverter ...
Kuanfang HE +3 more
doaj +1 more source