Results 221 to 230 of about 2,551,621 (293)

Diagnostic Use of Testing for Novel Murine Autoantibodies for Sjögren Disease in the Rheumatology Outpatient Setting

Arthritis Care &Research, EarlyView.
Objective The goal was to assess the diagnostic performance of three novel autoantibodies (NA) for Sjögren disease (SjD) by comparing NA prevalence in patients with SjD, other autoimmune rheumatic diseases (ARDs), nonspecific chronic sialadenitis (CS), and controls.
Chadwick R. Johr, Michael D. George, Vatinee Y. Bunya, Nora Sandorfi, Mina Massaro‐Giordano, Frederick B. Vivino   +5 more
wiley   +1 more source

Does Long‐Term Lower Extremity Strength Training in Adults With Knee Osteoarthritis and Varus Alignment Reduce Knee Joint Loading During Gait?

Arthritis Care &Research, EarlyView.
Objective We examined whether 18 months of strength training in individuals with knee varus alignment and medial tibiofemoral osteoarthritis (OA) reduced knee joint loads during walking compared to an attention control group. Methods This study was a secondary analysis of a randomized clinical trial that compared the effects of strength training to a ...
Stephen P. Messier, Matthew N. Vigliotti, Paige E. Rice, Brian Pietrosimone, Shannon L. Mihalko, Edward H. Ip, Richard F. Loeser, David J. Hunter, Ali Guermazi, Ryan Hill, Santiago Saldana, Kim L. Bennell, Paul DeVita   +12 more
wiley   +1 more source

Cracking the Code: Which Ocular Symptoms Predict Dry Eye Signs? Insights from a large international sicca registry

Arthritis Care &Research, Accepted Article.
Purpose The study aimed to identify symptom‐based predictors of dry eye disease (DED) signs in the Sjögrens International Collaborative Clinical Alliance (SICCA) cohort. Methods Retrospective analysis examining 16 ocular symptoms (most graded 0‐4) and artificial tear (AT) use (graded 0‐3) as predictors of DED signs [abnormal ocular surface staining ...
Pragnya R Donthineni, Chloe Shields, Rohit Muralidhar, Shreya Bhatt, Alan Baer, Robert Fox, Sara S. McCoy, Anat Galor   +7 more
wiley   +1 more source

Pain and Patient‐Reported Physical Function Did Not Differ Among Body Composition Profiles in Patients With Hip Osteoarthritis

Arthritis Care &Research, EarlyView.
Objective To explore whether higher body fat and lower lean mass are associated with greater pain and worse patient‐reported physical function in individuals with hip osteoarthritis (OA). A secondary aim was to examine whether pain and patient‐reported physical function differ according to four body composition profiles: high body fat, low lean mass ...
Alexandra Ryan, Boliang Wang, Fiona Dobson, Ben Kirk, Travis Haber, Kim L. Bennell, Shirley P. Yu, Kim Allison, Ricardo J. S. Costa, Gabrielle Knox, Michelle Hall   +10 more
wiley   +1 more source

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Advanced Engineering Materials, EarlyView.
Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer, Eric R. Hoglund, Anton V. Ievlev, Patrick E. Hopkins   +3 more
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source