Results 151 to 160 of about 38,626 (306)

Wind erosion on the north-eastern Tibetan Plateau: constraints from OSL and U-Th dating of playa salt crust in the Qaidam Basin [PDF]

, 2014
The arid Qaidam Basin is the largest (~3.88 x 10(4) km(2)) basin on the north-eastern Tibetan Plateau. Wind erosion in the area has been regarded as an important trigger for intra-basin tectonic balance upheaval, geomorphologic development and as a major
Ma, ZB (Ma, Zhibang)[ 4,5 ], Appel, E (Appel, Erwin)[ 7 ], Yu, LP (Yu, Lupeng)[ 6,10 ], Lai, ZP (Lai, Zhongping)[ 1,2,6 ], Han, WX (Han, Wenxia)[ 1,2,3 ], Fang, XM (Fang, Xiaomin)[ 8,9 ]   +5 more
core  

Triple Junctions as Dislocation‐Like Defects: The Role of Grain Boundary Crystallography Revealed by Experiment and Atomistic Simulation

Advanced Engineering Materials, EarlyView.
Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink, Saba Saood, Peter Schweizer, Jörg Neugebauer, Gerhard Dehm   +4 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Electrified Damage in Motion Systems

Advanced Engineering Materials, EarlyView.
The electrified damage in motion systems is a fundamental framework presenting the degradation pathway arising from the coupling of electrical energy transport with mechanical contact and interfacial chemistry. The framework positions electrified damage as a distinct degradation regime with unique characteristic surface morphologies and failures of ...
M. Humaun Kabir, Angelina Nguyen, Hong Liang   +2 more
wiley   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source

Investigating and applying rock surface luminescence dating in archaeological and geomorphological contexts [PDF]

Rock surface luminescence dating is a developing geochronological method which utilises the zeroing of the dose-dependent, optically sensitive luminescence signal at rock surfaces.
Ageby, Lucas
core  

High‐Resolution Corrosion Fingerprinting of Alloy Libraries via Microdroplet Spectroelectrochemistry

Advanced Engineering Materials, EarlyView.
Ionic‐liquid microdroplet spectroelectrochemistry enables stable, localized electrochemical measurements over extended timescales. By coupling impedance spectroscopy, wetting analysis, finite‐element simulations, and operando Raman spectroscopy, it disentangles geometrical and electrochemical effects, opening new opportunities for rapid corrosion ...
Ekaterina Kurchavova, Oumaïma Gharbi, Mireille Turmine, Vincent Vivier   +3 more
wiley   +1 more source

Uniform Amorphization of Crystalline Silicon Surfaces Enabled by Deep Ultraviolet Femtosecond Laser Pulses

Advanced Engineering Materials, EarlyView.
Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali, Magali Gregoire, Matys Guyard, Tatiana Itina, David Grojo, Pol Sopeña   +5 more
wiley   +1 more source

Model‐Guided Design of Paper Membrane Architectures for Controlled Flow and Enhanced Diagnostic Sensitivity

Advanced Engineering Materials, EarlyView.
Geometrical modifications on nitrocellulose membranes can result in observable differences in signal intensity relative to a reference membrane (top and bottom left). Using two reference experiments, we have developed a theoretical model that can reproduce the experimentally observed flow changes and provide information on membrane parameters, e.g ...
Maria Dimaki, Lea Holritz, Winnie E. Svendsen   +2 more
wiley   +1 more source

Biomass Native Structure Into Functional Carbon‐Based Catalysts for Fenton‐Like Reactions

Advanced Functional Materials, EarlyView.
This study indicates that eight biomasses with 2D flaky and 1D acicular structures influence surface O types, morphology, defects, N doping, sp2 C, and Co nanoparticles loading in three series of carbon, N‐doped carbon, and cobalt/graphitic carbon. This work identifies how these structural factors impact catalytic pathways, enhancing selective electron
Wenjie Tian, Jingkai Lin, Zhihao Tian, Selusiwe Ncube, Huayang Zhang, Emiliano Cortés, Hongqi Sun, Shaobin Wang   +7 more
wiley   +1 more source