Results 191 to 200 of about 289,838 (316)

Nondestructive Testing of Welded Composite Metal Foams

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva, Aman Kaushik, Afsaneh Rabiei   +2 more
wiley   +1 more source

Unsupervised learning of reference bony shapes for orthognathic surgical planning with a surface deformation network. [PDF]

Med Phys, 2021
Xiao D, Deng H, Lian C, Kuang T, Liu Q, Ma L, Lang Y, Chen X, Kim D, Gateno J, Shen SG, Shen D, Yap PT, Xia JJ.   +13 more
europepmc   +1 more source

Encyclopedia of 2D β′‐In2Se3 Growth Using Chemical Vapor Deposition: The Effects of Synthesis Parameters Onto Material Quality

Advanced Engineering Materials, EarlyView.
A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge, P. Sanju S. Panawala, Joseph F. S. Fernando, Zhenhuan Chen, Chao Zhang, Dong‐Chen Qi, Liangzhi Kou, Konstantin L. Firestein, Dmitri V. Golberg   +8 more
wiley   +1 more source

Constrained parameterization with applications to graphics and image processing.

Surface parameterization is to establish a transformation that maps the points on a surface to a specified parametric domain. It has been widely applied to computer graphics and image processing fields.
Yu, Hongchuan
core  

Accurate Measurement of Strain in Noncontact Surface Deformation Using Subset-Based Digital Image Correlation. [PDF]

Contrast Media Mol Imaging, 2021
Agnes Shifani S, Godwin Premi MS.
europepmc   +1 more source

Influence of Surface Finish on the Tribological Performance of AlTiBN Coatings Deposited on Forming Tools

Advanced Engineering Materials, EarlyView.
Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver, Iker Alfonso, Eneko Barba, Javier León, José Antonio García, Iñaki Zalakain, Iván Fernández Martínez, Arley García‐Carrero, Christian Almeyda, Daniel Salcedo   +9 more
wiley   +1 more source

InSAR surface deformation and numeric modeling unravel an active salt diapir in southern Romania. [PDF]

Sci Rep, 2021
Manea VC, Armaş I, Manea M, Gheorghe M.
europepmc   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Spatiotemporal Evolution and Drivers of Highway Surface Deformation Based on SBAS-InSAR and Geodetector. [PDF]

Sensors (Basel)
Chen Z, Li J, Zhang X, Bi J.
europepmc   +1 more source

Characterization of Groundwater Recharge and Flow in California's San Joaquin Valley From InSAR-Observed Surface Deformation. [PDF]

Water Resour Res, 2021
Neely WR, Borsa AA, Burney JA, Levy MC, Silverii F, Sneed M.   +5 more
europepmc   +1 more source