Results 141 to 150 of about 16,880,130 (352)

Processes governing the mass balance of Chhota Shigri Glacier (Western Himalaya, India) assessed by point-scale surface energy balance measurements

, 2014
Some recent studies revealed that Himalayan glaciers were shrinking at an accelerated rate since the beginning of the 21st century. However, the climatic causes for this shrinkage remain unclear given that surface energy balance studies are almost ...
M. Azam, P. Wagnon, C. Vincent, A. Ramanathan, V. Favier, Arindan Mandal, J. Pottakkal   +6 more
semanticscholar   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, EarlyView.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

Surface energy and the contact of elastic solids

Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences, 1971
K. Johnson, K. Kendall, A. D. Roberts
semanticscholar   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Comparison of the Rate Constants of ^•OH, SO₄^•−, CO₃^•−, Cl₂^•−, Cl^•, ClO^• and H^• Reactions with Organic Water Contaminants

Molecules
The reactions of 7 radicals, which play a key role in the degradation of water contaminants in Advanced Oxidation Processes, were discussed and compared. For evaluation of the reactivities and comparisons, the chemical reactivity rate constants were used,
László Wojnárovits, Erzsébet Takács
doaj   +1 more source

Understanding the Effect of Resistance Temperature Detector Temperature Controllers on Microstructural Alignment in Magnetic Freeze Casting

Advanced Engineering Materials, EarlyView.
The effect of temperature controllers that are commonly used in freeze‐casting is investigated in this work. Temperature controllers are observed to generate a voltage in the slurry. Microstructural alignment and ultimate compressive strength data show this voltage to interfere with the ability to align the microstructure using magnetic fields ...
Maddie A. Schmitz, Steven E. Naleway
wiley   +1 more source

Composite Electrospun Fibers Containing Optimized B‐ and Cu‐Doped Bioactive Glass Sol‐Gel Particles for Potential Soft Tissue Engineering Applications

Advanced Engineering Materials, EarlyView.
This article describes the preparation and characterization of poly(ε‐caprolactone) electrospun composite fibers incorporating sol‐gel‐derived bioactive glass particles doped with B and Cu. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, contact angle, acellular bioactivity, mechanical and ...
Elisa Piatti, Marta Miola, Liliana Liverani, Paolo Sartori, Enrica Verné, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Unlocking the Power of Quercetin‐Encapsulated Mesoporous Bioactive Glass Nanoparticles: A Multifunctional Approach to Bone Regeneration

Advanced Engineering Materials, EarlyView.
Mesoporous bioactive glass nanoparticles (MBGNs) are investigated for bone regeneration given their remarkable structural and functional properties. MBGNs are functionalized with Mn and Cu and incorporated with quercetin, a natural flavonoid exhibiting antioxidant, anti‐inflammatory, and antimicrobial properties.
Giovanni Lo Bello, Qaisar Nawaz, Pier Francesco Ferrari, Laura Pastorino, Roberto Raiteri, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Evaluation of the Potential of Laser Shock Peening Compared with Cold Expansion for Improving Fatigue Resistance of Riveted Lap Joints of Aerospace Grade 7175 Al Alloy

Advanced Engineering Materials, EarlyView.
This study investigates laser shock peening for enhancing fatigue performance of riveted aerospace aluminum joints. A comparative approach with cold expansion combines fatigue testing and synchrotron X‐ray methods. Integrating mechanical testing with residual stress and strain characterization provides insights into how different treatments affect the ...
Ogün Baris Tapar, David Osman Busse, Maximilian Sprengel, Domenico Furfari, Marc‐André Nielsen, Guilherme Abreu Faria, Jérémy Epp   +6 more
wiley   +1 more source