Results 41 to 50 of about 79,715 (260)
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Contemporary Clinical Dentistry, 2018 Statement of the Problem: Disinfection of complete dentures is very crucial to prevent cross-contamination and infection. Microwave disinfection is a quick, easy, and effective means to disinfect dentures. However, the effect of repeated microwave cycles
Priti Jaiswal +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Dental Journal, 2005 Acidity can bring about tooth erosion. A laboratory experiment about soft drink acidity to the hardness of tooth surface was done. The purpose of the study was to investigate the surface hardness of the tooth surface after immersion in some kinds of soft
Edhie Arif Prasetyo
doaj +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
WEAR RESISTANCE OF HARD TURNED SURFACES
Cutting & Tools in Technological System, 2022 The quality of working surfaces plays an important role in automotive industrial components. One of the main characteristics of such surfaces is their wear resistance. In this study external cylindrical surfaces were analyzed. A Design of Experiment methodology was applied and hard turning experiments were carried out to analyze the effects of the ...
openaire +3 more sources
Arc Quenching Effects on the Groove Shapes of Carbon Steel Tubes
MetalsThis study investigates the impact of arc-hardening parameters on a groove-shaped S45C steel tube, with a focus on surface hardness and microstructure.
Tran Minh The Uyen +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe +4 more
wiley +1 more source
Surface Structure Improvement of Mild Steel and Aluminium by Roller Burnishing [PDF]
Engineering and Technology Journal, 2015 In an experimental analysis study, a mix of burnishing parameters was varied to obtain the optimum roller conditions that produce superlative surface smoothness and hardness.
Majeed Nemat
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source