Results 121 to 130 of about 839,368 (266)

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Effect of Surface Morphology Formed by Additive Manufacturing on the Adhesion of Dental Cements to Zirconia. [PDF]

Materials (Basel)
Yoshihara K, Nagaoka N, Lee S, Maruo Y, Spirrett F, Kirihara S, Yoshida Y, Van Meerbeek B.   +7 more
europepmc   +1 more source

On‐Demand Activation of Thin Alginate Shell Encapsulated Volatile Liquid for Untethered Pneumatic Soft Actuation

Advanced Engineering Materials, EarlyView.
Phase‐changing liquids enable untethered pneumatic actuation in soft robotics but suffer from volatility and storage challenges. This work reports a simple method to encapsulate Novec 7000 within micron‐thin alginate shells via in situ injection and ionic crosslinking.
Rayan A. M. Basodan, Jack Keddie, Byoungyoul Park, Hyun‐Joong Chung   +3 more
wiley   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Thiophene structure influences plasmonic creatinine sensing through molecular interaction and surface morphology. [PDF]

Sci Rep
Zakaria NI, Nazri NAA, Azeman NH, Khushaini MAA, Othman MQ, Bakar MHA, Aziz THTA, Jamil MSM, Zain ARM, Bakar AAA.   +9 more
europepmc   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Evaluation of Shear Bond Strength and Surface Morphology (via SEM) of Different Provisional Crowns and Surface Treatments to PMMA. [PDF]

Int J Dent
Krassanairawiwong P, Srihatajati J.
europepmc   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Effect of Surface Morphology and Texture of Short-Tailed Shrew's Toe on Tribological Properties of 65Mn Steel. [PDF]

Biomimetics (Basel)
Zhang Y, Zhang J, Chen W, Wang H, Qiu Z, Wang W, Zhang Y, Li D.   +7 more
europepmc   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source