Results 11 to 20 of about 18,676,119 (274)

Geometrical properties of equipotential surfaces [PDF]

Proceedings of the American Mathematical Society, 1962
Jean‐Pierre Kahane
  +6 more sources

Surface Properties of Suberin [PDF]

Journal of Colloid and Interface Science, 1997
The surface energy of suberin was determined by four different methods, namely, (i) contact angle measurements, (ii) Wilhelmy plate measurements, (iii) maximum bubble pressure, and (iv) inverse gas chromatography (IGC). The first three methods gave a gammasub value in the range 40-50 mN m-1 at room temperature.
Cordeiro, Nereida, Aurenty, Patrice, Belgacem, Mohamed Naceur, Gandini, Alessandro, Neto, Carlos Pascoal   +4 more
openaire   +3 more sources

Novel insight on the local surface properties of ZnO nanowires

Nanotechnology, 2020
Novel insight on the local surface properties of ZnO nanowires (NW) deposited by the evaporation-condensation method on Ag-covered Si substrates is proposed, based on the results of comparative studies by using the scanning electron microscopy (SEM), x ...
M. Kwoka, Anna Kulis-Kapuscinska, D. Zappa, E. Comini, J. Szuber   +4 more
semanticscholar   +1 more source

In vitro effect of anodization of titanium abutments on their tensile bond strength to implant-supported lithium disilicate all-ceramic crowns

Dental Research Journal, 2023
Background: The retention of cement-retained implant-supported restorations can be affected by surface treatments such as anodizing. This study aimed to assess the effect of the anodization of titanium abutments on their tensile bond strength to implant ...
Hamed Karimi Pour, Homeira Ansari, Azita Mazaheri Tehrani   +2 more
doaj   +1 more source

Influence of N doping on structural and photocatalytic properties of hydrothermally synthesized TiO2/carbon composites [PDF]

Journal of the Serbian Chemical Society, 2023
N-doped TiO2/carbon composites (TiO2/CN) with different nitrogen content, were obtained starting from titanium isopropoxide and glucose, and by varying the amount of melamine, added to starting reaction mixture. For comparison, an undoped sample (TiO2/C)
Maletić Marina M., Kalijadis Ana M., Lazović Vladimir, Trifunović Snežana, Babić Biljana M., Dapčević Aleksandra, Kovač Janez, Vukčević Marija M.   +7 more
doaj   +1 more source

Plastron properties of a superhydrophobic surface [PDF]

, 2006
Most insects and spiders drown when submerged during flooding or tidal inundation, but some are able to survive and others can remain submerged indefinitely without harm.
Carole C. Perry, Ege R., F. Brian Pyatt, Glen McHale, Michael I. Newton, Neil J. Shirtcliffe, Rovner J. S., Thorpe W. H.   +7 more
core   +1 more source

A property of complete minimal surfaces [PDF]

Transactions of the American Mathematical Society, 1984
If M M is a complete minimal surface in R n {R^n} , we denote by W W the set of points in R n {R^n} that do not lie on any tangent plane of M M .
Hasanis, T., Koutroufiotis, D.
openaire   +3 more sources

Improvement of coreboards surface properties

Turkish Journal of Forestry, 2020
Coreboards are produced entirely from corrugated cardboard wastes and 165 to 450 g/m2 depending on the area of use and used as coil cores (tissue papers, bobbins, etc.).
Ahmet TUTUŞ, Umut SAKÇILAR, Mustafa ÇİÇEKLER   +2 more
doaj   +1 more source

Surface electronic properties of undoped InAlN alloys [PDF]

, 2008
The variation in surface electronic properties of undoped c-plane InxAl1−xN alloys has been investigated across the composition range using a combination of high-resolution x-ray photoemission spectroscopy and single-field Hall effect measurements.
Adikimenakis, A., Bailey, L. R., Georgakilas, A., Iliopoulos, E., King, Philip David, Lu, H., McConville, C. F., Schaff, William Joseph, Veal, T. D.   +8 more
core   +2 more sources

Surface performance of TC4 alloy repaired by laser cladding under different scanning speeds

Journal of Aeronautical Materials, 2023
In the current aviation industry, laser melting is an ideal technique for repairing and surface treatment of TC4 alloy parts, which has advantages over traditional metal repair techniques in terms of process.
CUI Jing, WANG Chengxuan, YANG Guangfeng
doaj   +1 more source