Results 91 to 100 of about 203,887 (298)
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Infection and the use of personal protective equipment among Primary Health Care workers during the COVID-19 pandemic [PDF]
Revista Latino-Americana de EnfermagemObjective: to analyze the frequency and associated risk factors for COVID-19 infection and the availability of Personal Protective Equipment used by primary healthcare workers.
Jarbas da Silva Ziani +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
, 2021 This study focuses on the existence of personal protective equipment surgical masks in the community of Mojokerto Regency and City. The problem is the difficulty of finding Personal Protective Equipment Surgical masks that meet the health standards which
Baidlowi, Imam
core
Advanced Engineering Materials, EarlyView.This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
, 2019 © 2018 Elsevier Ltd, BASO ∼ The Association for Cancer Surgery, and the European Society of Surgical Oncology. There are several suggestions that centralization of care improves outcome for rare cancers, particularly when optimal treatment requires ...
S. Bonvalot +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
, 1988 We present a ready-surgical resuscitation unit sponsored by Ospedale Maggiore of Milan and by Lombardy Region. Is a completely autonomous equipment and personnel within 24 hours which allows power to be on the place of a possible disaster (such as an ...
G. Sinigaglia, R. Azzoni
core