Results 171 to 180 of about 278,985 (299)

Elinvar Materials: Recent Progress and Challenges

Advanced Engineering Materials, EarlyView.
Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley   +1 more source

Evaluation of riverine macro- and mesoplastic monitoring approaches. [PDF]

Environ Monit Assess
Oswald SB, Vriend P, Ragas AMJ, Schoor MM, Collas FPL.   +4 more
europepmc   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

How does one health fit into current academic frameworks? Insights from a SWOT analysis by the North America One Health University Network. [PDF]

Front Med (Lausanne)
Berrian AM, Ferrara J, Matos A, Carmichael KP, Woods CW, Thakur S, Goldstein T.   +6 more
europepmc   +1 more source

PBF‐LB/M of Ti‐6Al‐4V: High‐Pressure Solution Treatment and Aging for Applications in a Sustainable Aerospace

Advanced Engineering Materials, EarlyView.
Additive manufacturing (AM) allows great geometric freedom for lightweight components. As parts are progressively optimized exploiting potentials in AM leading in smaller material cross sections, high pressure solution treating and aging (STA) treatments show an enormous potential for strongly improving material properties.
Mika León Altmann, Andre Danzig, Freerk Syassen, Rainer Fechte‐Heinen, Anastasiya Toenjes   +4 more
wiley   +1 more source

Challenges and Opportunities of Internship Method in Technologist Surgery Undergraduate Interns: A Qualitative Content Analysis Study. [PDF]

Iran J Nurs Midwifery Res
Bigdeli Shamloo MB, Rashidi N, Kalani L, Rokhafrooz D.   +3 more
europepmc   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Navigating challenges and opportunities: a SWOT analysis of digital management center implementation in county hospitals. [PDF]

Front Public Health
Zhou S, Yin H.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Policy innovation of construction waste management in Xi'an, China: A SWOT analysis of incentive mechanisms. [PDF]

PLoS One
Liu H, Yang S, Jusoh MNH.
europepmc   +1 more source