Results 151 to 160 of about 310,458 (332)

Enhanced Trapping with an Optimized Graphene‐Based Bowtie Plasmonic Nanotweezer: Design, Analysis, and Bioanalytical Applications

open access: yesAdvanced Photonics Research, EarlyView.
A graphene‐based bowtie plasmonic nanotweezer is designed and optimized using particle swarm optimization and transfer matrix analysis. The structure achieves strong field confinement, delivering trapping forces up to 6 nN W−1 for 10 nm bioparticles with sixfold lower power requirements than conventional designs.
Saba Ebrahimpanah   +2 more
wiley   +1 more source

Inverse‐Designed on‐Chip Terahertz Three‐Channel Mode and Wavelength Division Demultiplexer

open access: yesAdvanced Photonics Research, EarlyView.
An ultracompact terahertz demultiplexer is developed using a hybrid inverse design that combines genetic algorithms with topology optimization. The device enables simultaneous mode‐ and wavelength‐division multiplexing within a footprint smaller than two wavelengths.
Faqian Chong   +5 more
wiley   +1 more source

Sharp Diamond Needles for Single‐Photon Emission

open access: yesAdvanced Photonics Research, EarlyView.
We study the morphological evolution of single‐crystal diamond needles oxidized at 650–700 °C. Electron microscopy and photoluminescence reveal temperature‐ and time‐dependent sharpening, length reduction, and surface modifications affecting tip properties.
Mariam Quarshie   +9 more
wiley   +1 more source

Effects of inlet duct taper and air supply mode on flow field uniformity in cold air fermentation room

open access: yesShipin yu jixie
ObjectiveTo improve the uniformity of airflow in the cold air fermentation room.MethodsNumerical simulations were performed using Fluent software, with average velocity and velocity non-uniformity coefficient as evaluation indexes.
ZHANG Guorong   +5 more
doaj   +1 more source

Design Optimization of a Variable Stiffness Robotic Gripper with Passive Restoration Fabricated by Multimaterial 3D Printing

open access: yesAdvanced Robotics Research, EarlyView.
A multimaterial robotic gripper fabricated via multimaterial 3D printing integrates conductive thermopolymer joints with flexible elastomeric components. Joule heating enables precise joint‐level stiffness modulation, enhanced by embedded temperature sensors, passive shape restoration, and active cooling, enabling versatile manipulation capabilities ...
Daniel Jee Seng Goh   +4 more
wiley   +1 more source

Opioid Taper Is Associated with Subsequent Termination of Care: a Retrospective Cohort Study

open access: yesJournal of general internal medicine, 2019
H. Perez   +4 more
semanticscholar   +1 more source

Waveguide Photoactuators: Materials, Fabrication, and Applications

open access: yesAdvanced Robotics Research, EarlyView.
Waveguide photoactuators convert guided light into mechanical motion. Their tethered‐flexible design enables minimally invasive surgery and confined‐space robotics. This review aims to guide materials selection, device design, and system integration, accelerating the transition of waveguide photoactuators from laboratory prototypes to versatile ...
Minjie Xi   +4 more
wiley   +1 more source

A Covalent 3D CNT@rGO Nano‐Hybrid for High‐Efficiency Conductivity in Lithium‐Ion Batteries

open access: yesAdvanced Science, EarlyView.
A facile one‐step CVD strategy achieves high‐yield (7692.31%) growth of CNTs on rGO, forming a covalently bonded 3D CNT@rGO hybrid. This structure enables multidirectional conductive networks in LiFePO4 cathodes, delivering superior rate performance, high ICE (99.88%), and 96.32% capacity retention after 300 cycles at 1 C.
Junwen Tang   +10 more
wiley   +1 more source

Tapering antipsychotic medication: practical considerations

open access: yesPsychological Medicine, 2021
Mark A. Horowitz   +7 more
openaire   +5 more sources

A Degradable Bioinspired Flier with Aerogel‐Based Colorimetric Sensors for Environmental Monitoring

open access: yesAdvanced Science, EarlyView.
Biodegradable fliers are developed inspired by Tipuana tipu samaras, integrating cellulose nanocrystal aerogel (CNCa) sensors loaded with natural dyes for pH and ammonia detection. The lightweight, degradable fliers mimic natural morphology and aerodynamics, offering an eco‐friendly, scalable solution for in situ environmental monitoring after passive ...
Gianpaolo Gallo   +4 more
wiley   +1 more source

Home - About - Disclaimer - Privacy