Results 61 to 70 of about 2,162,906 (279)
Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys
Advanced Engineering Materials, EarlyView.An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.HEA interlayers offer a versatile route for joining high‐performance structural materials. Their compositional and structural design regulates interfacial reactions, suppresses brittle IMCs, and improves metallurgical bonding. Sandwich interlayers further integrate defect healing with precipitation strengthening, enabling improved strength–ductility ...
Lin Yuan +4 more
wiley +1 more source
New evaluation method of angle tear property of vulcanizates
Hecheng xiangjiao gongyeThe combination method of numerical simulation and experimental verification was used to optimize the current evaluation method of tear strength of rubber unnicked angle test piece.
ZHANG Wei, YANG Wen-zhen, HOU Xiao-qian
doaj +1 more source
Effect of Wool Fiber Incorporation into RTV Maxillofacial Prosthetic Silicone Elastomers
Dentistry 3000The estimated lifespan of silicone maxillofacial prostheses under clinical use is 1.5–2 years, necessitating the fabrication of new prostheses after expiration. The most common reason for prosthesis remanufacturing is the deterioration of the mechanical
Salah Khalaf, Mohammed R. Abduljabbar
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin +12 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.PUF/ENB microcapsules were synthesized based on a sequential factorial design and incorporated into an epoxy matrix. Their anticorrosive action, associated with the self‐healing mechanism, demonstrated that the addition of microcapsules to the coating improved anticorrosive performance compared to pure epoxy coatings, particularly when the encapsulate ...
Vandicleya Alves Moreira +6 more
wiley +1 more source
AlMg6 to Titanium and AlMg6 to Stainless Steel Weld Interface Properties after Explosive Welding
Metals, 2020 This paper studies the weld interface microstructure and mechanical properties of AlMg6-stainless steel and AlMg6-titanium bimetals produced using explosive welding.
Andrey Y. Malakhov +3 more
doaj +1 more source
, 2022 AIM AND OBJECTIVE: The aim and objective of this study was to evaluate and compare the tear strength of irreversible hydrocolloid impression material containing quaternary ammonium compound and silver nanoparticles with the conventional irreversible ...
Shanthi, C
core
Advanced Engineering Materials, EarlyView.Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar +3 more
wiley +1 more source
The Effect of Resorcinol on Alginate Tear Strength
Dentistry 3000The development of dental impression materials with antimicrobial efficacy is a significant biomedical research target. Alginate impression material is widely used in dental practice, and endeavours to enhance its properties remain a persistent ...
Hasanain K.A. Alalwan +4 more
doaj +1 more source